Bedienungsanleitung Denon AVR-688 (Seite 12 von 68) (Englisch)

584394

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite



Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting

ENGLISH

w q

w q w q w q w q

w q w qw q

(R)

(L) (R) (L) (R)

(L) (R) (L)

Speaker Connections

Example: 5.1-channels (FRONT A+B) and ZONE2 use

Front speakers

Center speaker

Subwoofer

with built-in

ampliﬁer

Surround speakers ZONE2 speakers

ZONE2

When using just one surround back speaker, connect it to the left channel (SBL).

NOTE

By default, the AVR-688’s “Amp Assign” setting is set to “ZONE2”. To use as the surround back speaker for

the main zone, change the “Amp Assign” setting (vpage 27).

b L : Left

R : Right



Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting

Front speakers

Connecting the Speaker Cables

Carefully check the left (L) and right (R) channels

and + (red) and – (black) polarities on the speakers

being connected to the AVR-688, and be sure to

interconnect the channels and polarities correctly.

Peel off about 0.03 ft/10 mm

of sheathing from the tip of

the speaker cable, then either

twist the core wire tightly or

terminate it.

Turn the speaker terminal

counterclockwise to loosen

it.

Insert the speaker cable’s

core wire to the hilt into the

speaker terminal.

Turn the speaker terminal

clockwise to tighten it.

When using a banana plug

Tighten the speaker terminal ﬁrmly before

inserting the banana plug.

NOTE

• Use speakers with an impedance of 6 to 16

Ω/ohms. When using front A and B speakers

simultaneously, use speakers with an impedance

of 12 to 16 Ω/ohms.

• Connect the speaker cables in such a way that

they do not stick out of the speaker terminals.

The protection circuit may be activated if the core

wires touch the rear panel or if the + and – sides

touch each other (v “Protection circuit”).

• Never touch the speaker terminals while the

power supply is connected. Doing so could result

in electric shock.

Protection circuit

If speakers with an impedance lower than speciﬁed

(for example 4 Ω/ohms speakers) are used for an

extended period of time with the volume turned

up high, the temperature may rise, activating the

protection circuit.

When the protection circuit is activated, the

speaker output is shut off and the power indicator

ﬂashes red. If this happens, unplug the power

cord, then check the speaker cable and input cable

connections. If the set is extremely hot, wait for it

to cool off and improve ventilation around it. Once

this is done, plug the power cord back in and turn

the set’s power back on.

If the protection circuit is activated again even

though there are no problems in the ventilation

around the set nor in the connections, the set may

be damaged. Turn the power off, then contact a

DENON service center.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon AVR-688 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Denon AVR-688

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info