Bedienungsanleitung Denon AVR-689 (Seite 12 von 71) (Englisch)

584395

Zoom out

Zoom in

Vorherige Seite

1/71

Nächste Seite

Speciﬁcations

w q

w q w q

w q

(R)

(L) (R)

(L)

Speaker Connections

Example: 5.1-channels

Front speakers

Center speakerSubwoofer

Subwoofer

with built-in

ampliﬁer

Surround speakers

NOTE

For surround back speakers :

• By default, the AVR-689’s “Amp Assign” setting is set to “ZONE2”. To use as the surround back speaker

for the main zone, change the “Amp Assign” setting (vpage 28).

• When using just one surround back speaker, connect it to the left channel (SBL).

For ZONE2 speakers :

• For multi-zone connection and operation, see “Amp Assign / Multi-zone Connections and Operations”

(vpage 51, 52).

b L : Left

R : Right



Connecting the Speaker Cables

Carefully check the left (L) and right (R) channels

and + (red) and – (black) polarities on the speakers

being connected to the AVR-689, and be sure to

interconnect the channels and polarities correctly.

Peel off about 0.03 ft/10 mm

of sheathing from the tip of

the speaker cable, then either

twist the core wire tightly or

terminate it.

Turn the speaker terminal

counterclockwise to loosen

it.

Insert the speaker cable’s

core wire to the hilt into the

speaker terminal.

Turn the speaker terminal

clockwise to tighten it.

When using a banana plug

Tighten the speaker terminal ﬁrmly before

inserting the banana plug.

NOTE

• Use speakers with an impedance of 6 to 16

Ω/ohms. When using front A and B speakers

simultaneously, use speakers with an impedance

of 12 to 16 Ω/ohms.

• Connect the speaker cables in such a way that

they do not stick out of the speaker terminals.

The protection circuit may be activated if the core

wires touch the rear panel or if the + and – sides

touch each other (v“Protection circuit”).

• Never touch the speaker terminals while the

power supply is connected. Doing so could result

in electric shock.

Protection circuit

If the core wires touch the rear panel and the

screws etc., or the ± sides touch each other, the

protection circuit will be activated and the power

indicator will ﬂash red at intervals of 0.5 secs.

If the protection circuit is activated, the speaker

output is isolated, and the power supply goes to

the standby state. If the power supply is turned

off, after the power supply cord is withdrawn,

please conﬁrm that speaker cable and input cable

are connected.

Also, if replaying large sound levels by using

a speaker having an impedance less than that

specified (eg, 4 Ω/ohms), the temperature will

rise, and the protection circuit might be activated.

The power supply will go into the standby state,

and the power indicator will ﬂash red at 2 second

intervals.

In this case, please switch off the power supply,

and wait until the AVR-689 has cooled down, and

the surrounding ventilation is good.

Even if there are no problems with the surround-

ing ventilation and connections, in the event of

the protection circuit becoming activated, due to

thinking that the AVR-689 has failed, please con-

tact DENON Service center after switching off.

Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon AVR-689 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Denon AVR-689

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info