Bedienungsanleitung Denon AVR-E200 (Seite 60 von 64) (Englisch)

547464

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

GAudioH

Symptom Cause/Solution Page

Audio is not output. •Check the connections for all devices.

•Check the speaker connections and conﬁgurations.

•Check whether the audio device power is turned on.

•Adjust the master volume.

•Cancel the mute mode.

•Select a suitable input source.

•Select a suitable input mode.

•Disconnect the headphones. No sound is output from the

speakers when headphones are connected.

6,7,10,11,

12,13

–

The volume does not

increase.

•The maximum volume is set too low. Set the maximum volume

using “Limit” on the menu.

•Power for external devices connected to the output connectors

of the unit may not be turned on. Check the power of connected

external devices.

–

No sound is

produced from

surround speakers.

•Check if the surround speakers are connected to the SURROUND

terminals.

–

No sound is

produced from

subwoofer.

•Check the subwoofer connections.

•Turn on the subwoofer’s power.

•Set “Speaker Conﬁg.” – “Subwoofer” on the menu to “Yes”.

•If “Front” and “Center” for “Speaker Conﬁg.” are set to “Large”,

and “SW Mode” is set to “LFE”, no sound may be output from

the subwoofers, depending on the input signal or selected

surround mode.

–

DTS sound is not

output.

•Set “Decode Mode” on the menu to “Auto” or “DTS”.

Dolby TrueHD, DTS-

HD, Dolby Digital

Plus audio is not

output.

•Make HDMI connections.

Dolby PLg mode or

DTS NEO:6 mode

cannot be selected.

•Check that “Speaker Conﬁg.” – “Center” or “Surround” is set

to other than “None”. If the speaker system is 2.0/2.1ch, this

surround mode cannot be selected.

•When headphones are used, Dolby PLg or DTS NEO:6 cannot be

selected.

–

RESTORER cannot

be selected.

•Check that an analog signal or PCM signal (fs=44.1/48 kHz) is

input. For playback of multi-channel signals such as Dolby Digital

or DTS surround, RESTORER cannot be used.

GRadioH

Symptom Cause/Solution Page

Reception fails, or

there is a lot of noise

or distortion.

•Change the antenna orientation or position.

•Separate the AM loop antenna from the unit.

•Use an FM outdoor antenna.

•Separate the antenna from other connection cables.

GRemote Control UnitH

Symptom Cause/Solution Page

The set cannot be

operated with the

remote control unit.

•Batteries are worn out. Replace with new batteries.

•Operate the remote control unit within a distance of about 23 ft/7

m from this unit and at an angle of within 30°.

•Remove any obstacle between this unit and the remote control

unit.

•Insert the batteries in the proper direction, checking the q and

w marks.

•The set’s remote control sensor is exposed to strong light (direct

sunlight, inverter type ﬂuorescent bulb light, etc.). Move the set

to a place in which the remote control sensor will not be exposed

to strong light.

Basic instructions

Advanced instructions

InformationInformation

DVD

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon AVR-E200 Seite 60

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Denon AVR-E200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info