Bedienungsanleitung Denon dht-500sd (Seite 6 von 69) (Deutsch)

370600

Zoom out

Zoom in

Vorherige Seite

1/69

Nächste Seite

ENGLISH

CAUTIONS ON HANDLING DISCS

Discs

Only the discs including the marks shown on page 5

can be played on the ADV-500SD.

Note, however, that discs with special shapes (heart-

shaped discs, hexagonal discs, etc.) cannot be played

on the ADV-500SD. Do not attempt to play such discs,

as they may damage the player.

Holding Discs

Avoid touching the surface of discs when loading and

unloading them.

Be careful not to get

fingerprints on the signal

surface (the side which

shines in rainbow colors).

Cleaning Discs

Fingerprints or dirt on the disc may lower sound and

picture quality or cause breaks in playback. Wipe off

fingerprints or dirt.

Use a commercially available disc cleaning set or a

soft cloth to wipe off fingerprints or dirt.

Wipe gently from the

middle outwards.

Do not wipe with a

circular motion.

NOTE:

• Do not use record spray or antistatic. Also do not

use volatile chemicals such as benzene or

thinner.

Record

spray

Thinner

Benzene

Cautions on Handling Discs

• Do not get fingerprints, grease or dirt on discs.

• Be especially careful not to scratch discs when

removing them from their cases.

• Do not bend discs.

• Do not heat discs.

• Do not enlarge the center hole.

• Do not write on the labeled (printed) side with a ball-

point pen or a pencil.

• Water droplets may form on the surface if the disc

is moved suddenly from a cold place to a warm one.

Do not use a hairdryer, etc., to dry the disc.

Cautions on Storing Discs

• Always eject discs after playing them.

• Keep discs in their cases to protect them from dust,

scratches and warping.

• Do not put discs in the following places:

1. Places exposed to direct sunlight for long periods

of time

2. Humid or dusty places

3. Places exposed to heat from heaters, etc.

Cautions on Loading Discs

• Only load one disc at a time. Loading one disc on

top of another may result in damage or scratch the

discs.

• Load 8 cm discs securely in the disc guide, without

using an adapter. If the disc is not properly loaded,

it may slip out of the guide and block the disc tray.

• Be careful not to let your fingers get caught when

the disc tray is closing.

• Do not place anything but discs in the disc tray.

• Do not load cracked or warped discs or discs that

have been fixed with adhesive, etc.

• Do not use discs on which the adhesive part of

cellophane tape or glue used to attach the label is

exposed, or discs with traces of tape or labels that

have been peeled off. Such discs may get stuck

inside the player, resulting in damage.

CONNECTIONS

CAUTION:

• Switch off the power to all equipment before making connections.

• Read the instructions of each component you intend to use with this unit.

• Be sure to insert each plug securely. To prevent hum and noise, avoid bundling the signal interconnection

cables together with the AC power cord or speaker cables

(1) Connection to a TV and other equipment

Connect the unit using one of the following terminations to your TV or monitor. The connections are listed in

order of quality of picture from the best possible first. Additional information on each connection type is

provided below:

If your TV or monitor is compatible with progressive scan, connect the TV via the COMPONENT VIDEO jacks

using a component video cable, and press the “PROGRESSIVE SCAN” button on the front panel so that

“P.SCAN” lights on the display. This results in a high quality picture with little flickering.

Progressive video signals are output from only component terminals.

Connecting the RGB SCART output(AV CONNECTOR) using an RGB-ready SCART cable, or connecting the

COMPONENT VIDEO using a component video cable is next to it.

S-VIDEO is your third choice.

Composite video output (SCART-COMPOSITE or VIDEO OUT) would be your last choice.

• For better picture quality, do not connect more than one video cable.

• Please connect this unit to a TV directly. If the TV is connected through a video cassette recorder, playback

of a copy protected DVD disc could result in distorted picture quality.

COMPONENT VIDEO jack

If your TV or monitor has COMPONENT VIDEO IN jacks, connect them with a quality component video cable.

In the default setting, COMPONENT VIDEO OUT jack is not active. If you want to use COMPONENT VIDEO

OUT, follow the following steps.

1. Connect the VIDEO jacks with a RCA video cable.

You can use the provided cable.

2. Connect the COMPONENT VIDEO jacks with a component video cable.

3. Turn the unit and TV on, and select “COMPONENT” in the DVD SETUP menu.

4. Turn the unit off and disconnect the RCA video cable from the VIDEO jacks.

COMPONENT VIDEO IN

R/CR PB/CB

ADV-500SD

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon dht-500sd Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Denon dht-500sd

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info