Bedienungsanleitung Denon DHT-E251BA (Seite 39 von 64) (Englisch)

584587

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Speakers

Setting items Setting details

Set Defaults

The “Levels” settings are

returned to the default

settings.

Yes : Reset to the defaults.

No : Do not reset to the defaults.

When you select “Set Defaults” and press

ENTER, the “Return settings to the default?”

prompt is displayed. Select either “Yes” or

“No”, and press ENTER.

BACK SETUP

ENTER

Crossovers Default settings are underlined.

Set the maximum frequency of the bass signal output from each channel to the subwoofer.

Set the Crossover Frequency to suit the bass reproduction capability of the speaker being used.

Setting items Setting details

Front / Center / Surround

Select speaker for setting of

crossover frequency.

40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /

250Hz : Set the crossover frequency.

•“Crossovers” can be set when the “Bass” – “SW Mode” (vpage36)

setting is “LFE+Main”, or when you have a speaker that is set to

“Small”.

•The default crossover frequency is “80Hz”, which will work best with the

widest variety of speakers. When using very small speakers, however,

you can choose a higher setting based on the speciﬁed frequency

response of the speakers. If the speaker has a speciﬁed frequency

response of 120 Hz – 20 kHz (as an example), then choose the 120 Hz

crossover frequency.

•For speakers set to “Small”, low frequency content below the crossover

frequency is attenuated to the speakers and the low bass content is then

re-delivered to the subwoofer(s), or the front (L/R) speakers if they have

been set to Large.

Bass Default settings are underlined.

Set subwoofer and LFE signal range playback.

Setting items Setting details

LPF for LFE

Set LFE signal playback

range. Set this when you

want to change the playback

frequency (low pass ﬁlter

point) of the subwoofer.

80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / 250Hz : Set LFE

signal range playback.

SW Mode

Select low range signals

to be reproduced by

subwoofer.

LFE : The low range signal of the channel set to “Small” speaker size is

added to the LFE signal output from the subwoofer.

LFE+Main : The low range signal of all channels is added to the LFE

signal output from the subwoofer. This is usually the best setting for most

systems.

•“SW Mode” can be set when “Speaker Conﬁg.” – “Subwoofer”

(vpage35) is set to other than “No”.

•Play music or a movie source and select the mode offering the strongest

bass.

•Select “LFE+Main” if you want the bass signals to always be produced

from the subwoofer.

NOTE

If “Front” and “Center” for “Speaker Conﬁg.” are set to “Large”, and

“SW Mode” is set to “LPF for LFE”, no sound may be output from the

subwoofers, depending on the input signal or selected surround mode.

Basic instructions

Advanced instructions

Information

Advanced instructions

DVD

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon DHT-E251BA Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Denon DHT-E251BA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info