614631
18
Zoom out
Zoom in
Vorherige Seite
1/28
Nächste Seite
11
EFX SENDEFX INS BEATo,p
TAP
EFX ON/OFF
EFX INS
EFX SELECT
EFX CUE
EFX DRY/WET
EFX FREQ.
Operating the effector
1
Press EFX SEND for the channel that you want to
apply the effector to.
The input source sound signal is sent to the effector.
To apply the effector to the mic input or master output, press
EFX INS.
2
Set the BPM.
BPM is the base value for the effector. To obtain normal
effects, match the BPM value with the BPM of the track.
The following three setting methods are available for the BPM
value.
n Setting Auto BPM
q Press TAP for more than 1 second.
”Auto” is shown in the display.
TAP LED lights up green.
w
Press TAP (short push).
The measured auto BPM value is displayed, and that value
is locked.
TAP LED switches off.
n Setting Manual In BPM
q Press TAP for more than 2 seconds.
The BPM value in the display flashes.
w Press BEAT to set the desired BPM value.
e Press TAP.
The setting is complete.
n Setting Manual TAP BPM
q Repeatedly press TAP in time with the input source rhythm.
The BPM value for the interval between button presses
is set.
3
Select the effector using EFX SELECT .
4
Press EFX ON/OFF to switch the effect ON.
EFX ON/OFF lights up.
Press EFX ON/OFF again to turn the effect off.
n Adjusting the effects
Rotate EFX FREQ.
Adjust the filter cut off frequency, and adjust the frequency band
within which to apply the effect.
This does not operate during SEND/RTN.
n To monitor the effect sound
Press EFX CUE.
Off
On
When this is switched on, the effect volume can be monitored even
when the effect is off. (Excluding ECHO and REVERB. )
n To adjust the proportion of
original volume and effect volume
Rotate EFX DRY WET.
When rotated in the DRY direction, the original volume proportion
increases.
When rotated in the WET direction, the effect volume proportion
increases.
Beat setting
Adjust the beats based on the set BPM value.
The setting range for beats differs depending on the effector.
Press BEAT to select the set beat value.
The beat display switches.
GSelectable rangeH
When REVERB/FLANGER/B·BREAKER/FILTER/B·SCRATCH are
selected:
1/4 - 32
When ECHO/DELAY/LOOP are selected:
1/16 - 4
18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Denon DN-X600 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Denon DN-X600

Denon DN-X600 Bedienungsanleitung - Deutsch - 28 seiten

Denon DN-X600 Bedienungsanleitung - Holländisch - 28 seiten

Denon DN-X600 Bedienungsanleitung - Französisch - 28 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info