Bedienungsanleitung Denon DSD-300 Cocoon portable (Seite 27 von 39) (Englisch)

498638

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

n Notes concerning use of “Firmware Update”

•Do not turn off the power until updating or upgrading is completed.

•Even with a broadband connection to the Internet, approximately

20 minutes is required for the updating procedure to be

completed.

•Once updating starts, normal operations on this unit cannot be

performed until updating is completed. Furthermore, updating

the ﬁrmware may reset the backup data for the parameters, etc.

set for this unit.

•If the update fails, remove and re-insert the power cord. “Update

Retry” appears on the display and update restarts from the point

at which update failed. If the error continues despite this, check

the network environment.

See the DENON website for details about updates.

Setting the network (Network Info.)

Firmware Update

•In order to update the ﬁrmware, the environment and settings

required for connecting to broadband internet are needed

(vpage8)

•Perform the ﬁrmware update operation after at least 2 minutes has

elapsed since turning this unit’s power ON.

Press + and – at the same time.

Turns on the menu settings mode and the menu appears on the

display (vpage20 “Menu map”).

Press + or – to select “Firmware Update”, then press

13.

Press + or – to select “Check for Update” or “Start”,

then press 13.

Check for Update

Check for ﬁrmware updates.

Use

+ or – to select the item, and press 13.

•Up to Date: It is already the latest ﬁrmware.

•Available Yes: Updates to the latest ﬁrmware.

•Available No: Does not update to the latest ﬁrmware.

Start

Determines whether to update or not.

Use

+ or – to select the item, and press 13.

•Yes: Performs update.

•No: Does not perform update.

•If updating fails, the set automatically retries, but if updating is still

not possible, one of the messages shown below is displayed. If

the display reads as shown below, check the settings and network

environment, then update again.

Display Description

Updating fail Updating failed.

Server is busy Server is busy. Wait a while then try again.

Connection fail Failure in connecting to server.

Download fail Downloading of the ﬁrmware has failed.

Auto standby

With the Auto Standby ON, this unit will automatically enter the

standby mode after about 30 continuous minutes of stop mode with

no operation.

•The default setting for the Auto Standby mode is “On”.

Move the power operation slide

switch on the rear panel from

“OFF” to “ON”.

“Always Display Clock?” is displayed.

Press + or – to select “Yes” or

“No”, then press 13.

Yes

(Auto Satandby Off)

The unit does not go into standby automatically.

(Auto Satandby On)

The unit goes into standby after 30 minutes.

NOTE

In the following situations, the Auto standby function does not operate.

•When iPod or iPhone is connected to the Dock connector on this

unit.

•When the input source is “AUX” and a devices connected to the

AUX IN jack.

•When the input source being played is “Internet Radio”or “Music

Server”.

Preparations

Operations

Informations

Operations

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon DSD-300 Cocoon portable Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Denon DSD-300 Cocoon portable

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info