Bedienungsanleitung Denon DVD-1800BD (Seite 10 von 26) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

68569

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Introduction Introduction

ENGLISH

Keep in mind the following when using the remote control:

• Make sure that there are no obstacles between the remote

control and infrared sensor window on the unit.

• Remote operation may become unreliable if strong sunlight or

fluorescent light is shining on infrared sensor window of the

unit.

• Remote control for different devices can interfere with each

other. Avoid using remote control for other equipment located

close to the unit.

• Replace the batteries when you notice a fall off in the operating

range of the remote control.

• The maximum operable ranges from the unit are as follows.

If you have other DENON’s DVD players around this unit, this unit

reacts to the commands you made for DVD players through its

remote control. To avoid this situation, you can set this unit not

react to other DENON’s DVD player’s remote control.

1) In stop mode, press [SETUP].

2) Press [7],[8],[9],[2].

3) Press [SETUP].

• “Only Attached Remocon” will be displayed on the upper

right corner of the screen and this unit only react to the

commands from this unit’s remote control.

• To set back to default, press [7],[8],[9],[1] at step 2. “Normal

Remocon” will be displayed on the upper right corner of the

screen and this unit react to both the commands from this unit’s

remote control and the other DENON’s DVD players’ remote

control.

To avoid the other DENON’s BD players responding the remote

signal of this unit, you can change the signal code of the remote

control. If the signal code of the remote control does not match to

the signal code of the unit, you cannot control the unit with the

remote control.

Ⅵ Change the signal code of the unit

1) In stop mode, press [SETUP].

2) Use [Y / Z] to select , then press [ENTER].

3) Use [Y / Z] to select , then press [ENTER].

4) Use [U / V] to select “Remote Control Setting”.

5) Press [ENTER] to select “DENON1” or “DENON2”.

6) Press [SETUP] to exit.

• At this point the new signal code of the unit is effective. Please

change the signal code of the remote control to match to the

signal code of the unit with following procedure.

Ⅵ Change the signal code of the remote control

Set to “DENON1”:

Press and hold [RETURN], and press [3], [2], [1].

Set to “DENON2”:

Press and hold [RETURN], and press [1], [2], [3].

• If the signal code does not match, the signal code of the remote

control will be displayed on the front panel display.

• The default setting and the setting after you change the

batteries is “DENON1”.

About the Remote Control

Loading the Batteries

A Open the battery

compartment cover.

B Insert two “R6P” (AA)

batteries, with each one

oriented correctly.

C Close the cover.

Cautions on Batteries

• Use “R6P” (AA) batteries in this remote control.

• Replace the batteries with new ones approximately once a

year, though this depends on the frequency with which the

remote control is used.

• If the remote control does not operate within a close

proximity of the main unit, replace the batteries with new

ones, even if less than a year has passed.

• The included batteries serve only for verifying operation.

Replace them with new batteries as soon as possible.

• When inserting the batteries, be careful to do so in the

proper direction, following the and marks in the remote

control’s battery compartment.

• To prevent damage or battery fluid leakage:

- Do not mix a new battery with an old one.

- Do not mix two different types of batteries such as alkaline

and manganese.

- Do not short-circuit, disassemble, heat or dispose of

batteries in flames.

• Remove the batteries when not planning to use the remote

control for a long period of time.

• If the batteries should leak, carefully wipe off the fluid from

the inside of the battery compartment, then insert new

batteries.

Using a Remote Control

- Line of sight: approx. 7 m

- Either side of the centre: approx. 7 m within 30°

Setting this Unit not React to Other DENON’s DVD Player’s Remote Control

Note

• The setting remains after you turn off this unit or unplug the

AC cord.

• If you try to operate this unit with the other DENON’s DVD

players’ remote control, some of the operation may not be

available depending on the manufactured year or type of the

remote control.

30°30°

7 m 30° 7 m 7 m 30°

Changing the Signal Code of a Remote Control

Angle Icon

Screen Saver On

Others

Off

Auto Power Off

Panel Display

Slide Show 5sec

Bright

DivX(R) VOD

Remote Control Setting

DENON1

E5J60ED_EN.book Page 6 Saturday, September 27, 2008 4:59 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon DVD-1800BD Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Denon DVD-1800BD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info