Bedienungsanleitung Denon POA-A1HDCI (Seite 8 von 18) (Englisch)

584591

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

Connections and Settings

NOTE

• Do not plug in the power cord until all connections have been completed.

• When making connections, also refer to the operating instructions of the other components.

• Be sure to connect the left and right channels properly (left with left, right with right).

• Do not bundle power cords together with connection cables. Doing so can result in humming or noise.

Connections for all compatible audio signal formats are described in these operating instructions.

Please select the types of connections suited for the equipment you are connecting.

With some types of connections, certain settings must be made on the POA-A1HDCI. For details,

refer to the instructions for the respective connection items below.

Audio cables Signal direction

Analog connections (XLR)

Balanced cable

Analog connections (RCA)

Pin-plug cable

Speaker connections

Speaker cables

Audio signal:

Output

Input

Output

Cables Used for Connections

Select the cables according to the equipment being connected.

Preparations

Carefully check the left (L) and right (R) channels and + (red) and – (black) polarities on the speakers being

connected to the POA-A1HDCI, and be sure to interconnect the channels and polarities correctly.

Peel off about 0.03 ft / 10 mm of sheathing from the tip of the speaker

cable, then either twist the core wire tightly or terminate it.

Turn the speaker terminal counterclockwise to loosen it.

Insert the speaker cable’s core wire to the hilt into the speaker

terminal.

Turn the speaker terminal clockwise to tighten it.

NOTE

• Connect the speaker cables in such a way that they do not stick out of the speaker terminals. The

protection circuit may be activated if the core wires touch the rear panel or if the + and – sides touch each

other (vProtection circuit).

• Never touch the speaker terminals while the power supply is connected. Doing so could result in electric

shock.

Protection circuit

If speakers with an impedance lower than speciﬁed are used for an extended period of time with the

volume turned up high, the temperature may rise, activating the protection circuit.

When the protection circuit is activated, the speaker output is shut off and the power indicator ﬂashes

red. If this happens, unplug the power cord, then check the speaker cable and input cable connections.

If the set is extremely hot, wait for it to cool off and improve ventilation around it. Once this is done, plug

the power cord back in and turn the set's power back on.

If the protection circuit is activated again even though there are no problems in the ventilation around the

set nor in the connections, the set may be damaged. Turn the power off, then contact a DENON service

center.

Connecting the speaker cables

When using a banana plug

Tighten the speaker terminal ﬁrmly before inserting the banana plug.



Getting Started Connections and Settings Operations Troubleshooting

1.POA-A1HDCIEU.indd 8 2008/01/18 11:06:59

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon POA-A1HDCI Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info