Bedienungsanleitung Denon RBD-X1000 (Seite 44 von 60) (Englisch)

578715

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

ENGLISHENGLISH

Auto standby

With the auto standby on, this unit will automatically enter the standby

mode after about 30 continuous minutes of stop mode with no

operation.

Press SETUP.

Use ui to select “AUTO

STANDBY”, then press ENTER

or p.

Use ui to select “ON”, then press ENTER or p.

The setting is entered.

NOTE

In the following situations, the Auto standby function does not operate.

• When an iPod or USB memory device is connected to the USB1 port

on the unit.

• When the input source is “TUNER”, “AUX1” or “AUX2”.

• When the input source is “AUX1/DOCK”, and an iPod is connected

to control dock for iPod. (ASD-11R only)

• When the input source is “PORTABLE IN” and a device is connected

to the portable jack.

Other functions

Auto power on

When the power is in standby, the power turns on when any of the

buttons below other than POWER ON on the remote control unit

or ON/STANDBY on the main unit is operated, and the respective

operation is performed.

The disc tray opens.

1 or 1/3

The input source selected directly

before the power was switched to

standby is played back.

• If the last input source was “DISC/

USB2”, “AUX1”, “AUX2” or

“PORTABLE IN”, the disc set in the

main unit is played back. (Certain

types of disc cannot be played

back.)

• When the control dock for iPod

is connected to the AUX IN 1

connectors and the input source is

“AUX1/DOCK”, the control dock

for iPod starts playing when 1 is

pressed.

DISC

The input source switches to “DISC/

USB2” and the disc starts playing.

(When “Optical Disc AutoPlay”

(vpage34) is “On”)

TUNER

Playback of the tuner starts.

USB1/iPod

The input source switches to “USB1/

iPod” and the USB memory device

starts playing.

AUX

The input source switches to “AUX”.

Last function memory

This stores the settings as they were immediately before going into

the standby mode.

When the power is turned back on, the settings are restored to as

they were immediately before going into the standby mode.

Registering preset codes

Registering preset codes on the supplied remote control unit will

enable turning on/standby and selecting the input source of your TV

using the remote control.

Use the preset codes table at the end of this manual to register the

preset codes.

Buttons used for operating the TV

• TV POWER

• TV INPUT

Press and hold POWER OFF and

SLEEP for at least 3 seconds.

The signal transmission indicator ﬂashes

twice.

Press 0 – 9 and input the 4-digit

number of the brand of the

component to be preset. The

numbers are shown in the preset

code table (vEnd of this

manual).

• Some manufacturers use more than one type of remote control code.

Refer to the included list of preset codes to change the number and

verify correct operation.

• The default setting is “Sony”.

NOTE

Depending on the model and year of manufacture of your equipment,

some buttons may not operate.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon RBD-X1000 Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Denon RBD-X1000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info