Bedienungsanleitung Denon RC-770 Universal (Seite 5 von 12) (Englisch)

459924

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

To clear

buttons in section

Í)

Select the

LCD

oattern

Íor the

source

(for

example

DBS) to be

cleared

using the buttons

in sec-

tion

then

pressing

the RESET

button

(())

with the tip oí

pen,

press

the button

in section

(DBS/TV

in this case) to

clear the

DBS

pattern.

(The

pattern

not cleared.l

To clear

the buttons

in sec-

tions

O, O, @

and

Simultaneously

press

the

RESET button

(O)

with

the

tip oÍ

Pen

and

the

POWER

button

(O).

All

the buttons

sections

O, O,

and

are

cleared.

Clearing opeÍation

1. Changing stored

codes

Follow the instructions

for storing

codes on

page

6, 7 to

store

the new code.

When a

new code

stored

at a

certain

button, the code

previously

stored at that

button is

cleaÍed,

but the codes

stored

at other buttons

remain.

2. Clearing stored

codes

(restoring

the

preprogrammed

codes)

Press the USE/LEARN

button

(O)

with the tip of a

pen.

(Both

"USE"

and

"LEARN" flash on the

LCD.)

Selecting Patterns from

the LGD

The LCD

patterns

can be selected by

pressing

the buttons in

section

as follows:

DBS/TV

DBS

pattern

VDPI-2

+VDPl

pattern

VDP 2

Dattern

LCD

pattern

TUNER

patteÍn

V-AUX

pattern

VDP1

pattern

VCR1

pattern

VCR2

pattern

DBS

pattern

DECK

pattern

DECK 2

oattern

vcRl-3

+vcRlpattern

+vcR2ï;,f;ïor*"ï

CD/AUX

pattern

AUX

pattern

V-AUX

PatternJ

DECK1-2

+DECKlpattern

*DECK2pattern

DAT1-2

+DATlpattern

*DAT2pattern

TUNER

pattern

RECEIVER

pattern

SURROUND+ SURROUND

Fêttêrn

SYSTEM ENTRY

pattern

The LCD

pattern

changes whenever

any of the signal codes

in the buttons in section

are transmitted. The

pattern

changes according to the initial settings, regardless

whether

a code has been stored at the button

not.

The LCD

patterns

corresponding to the various

buttons are

as follows:

Buttons in section

TUNER

AUX

VDP

VCRl

VCR2

DBS

DAT/TAPE1

DAT/TAPE2

Buttons in

section

SURROUND

pattern

The LCD

pattern

does

not switch for

other buttons. The

patern

is displayed.

The LCD

pattern

is displayed, when

any buttons

are

pressed.

The LCD

pattern

turn off automatically

approximately 10

seconds after the last button is

pressed.

"CLEAR"

is disPlaYed.

Both

"USE" and

"LEARN"

flash on

the LCD.

The codes

you

have

stored are

cleared,

and the codes

preprogrammed

DENON are

restored.

ïhe

other

buttons are

cleared

as well.

Press the USE/LEARN

button

(O)

again to set the use

mode.

("USE"

and

"LEARN"

disappear.l

Remote contÍol

opêÍation

1. Check that

both

"USE" and

"LEARN"

are

off'

2. lf

both

"USE" and

"LEARN"

are

flashing

"IEARN"

is lit,

press

the USE/LEARN

button to

turn

"USE" and

"LEARN" off.

When

a remote

control

operation

button

press-

ed,

"USE" lights

and

the remote

control

code

transmitted.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon RC-770 Universal Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info