Bedienungsanleitung Denon s 52 (Seite 31 von 39) (Englisch)

160360

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite



Getting Started Connections Setup Information Troubleshooting

ENGLISH

Playback

• When the input source is “Internet Radio”, “PC Music”, “iPod”, or

“CD”, if music does not play when the alarm on time is reached, a

Beep will sound.

• Alarms 1 and 2 operate separately.

• If the set is not operated for 60 minutes after alarm playback starts,

playback stops and the function off (The Beep sound stops after 5

minutes).

• When you want alarm playback of an iPod recording, set iPod while

pausing the track you want to play.

n Pausing alarm playback (snooze function)

Press <MUTE / SNOOZE> during alarm playback.

Alarm playback resumes 5 minutes after it was stopped.

n Stopping alarm playback

Either press <ALARM1> or <ALARM2> on the main unit to turn the

alarm off, or press the main unit’s <FUNCTION ON/OFF>.

If there is a power failure

n When connected to a network

When the power comes back on, the set automatically connects

to an SNTP (Simple Network Time Protocol) server and the current

time is adjusted automatically. Once the zone, daylight saving time

and alarm time have been set, they are stored in the memory, so

there is no need to set them again.

n When unconnected to a network

When the power comes back on, the clock resumes from the time

the power turned off. If the time is way off, turn the power on and

reset the current time. If the alarm time has been set, it is stored in

the memory, so there is no need to set it again.

Alarm Setting

Set the alarm time, source and volume.

Press <ALARM SETTING> to set the alarm.

GAlarm number selectionH

Turn <Multi Jog> to select “ALARM1” or

“ALARM2”, then press ENTER.

GAlarm time settingH

Select time with <Multi Jog>, then press ENTER to

set.

b Turn <Multi Jog> clockwise to increment the set value, and counter-

clockwise to decrement it.

GAlarm source settingH

Select alarm source with <Multi Jog>, then press

ENTER to set.

GAlarm volume level settingH

Select alarm volume level with <Multi Jog>, and

press ENTER to set.

6

Press <ALARM1> or <ALARM2>, and set the alarm

on.

Advanced Operation

Set the current time (vpage 11).

During playback, use SLEEP to select the time.

120 90 60 50 40 30 20 10

b After about 5 seconds, the previous display reappears and the

timer starts.

The power is set to the function off mode after the set

amount of time.

Off

Setting the Sleep Timer

Use this function to automatically switch the power to

the function off mode after a speciﬁc amount of time

(minutes).

Canceling the sleep timer

Press SLEEP, select “Off” from the sleep timer time display.

Checking the time remaining until the sleep timer

starts

Press SLEEP.

Checking the current time

Press [DISPLAY] or hold down DIMMER for 2 seconds or more.

The time is displayed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon s 52 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Denon s 52

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info