46
ENGLISH
System Setup System Setup
ENGLISH
3
-1
When “INPUT MODE” is selected:
Press the CURSOR
•
or
ª
button to select the
desired setting item, then press the ENTER
button.
AUTO (Factory default):
In this mode, the type of signal being input to the digital and
analog input terminals is detected and the program in the
set’s surround decoder is switched automatically to play the
signals for the selected input function.
The presence or absence of digital signals is detected, the
signals input to the digital input are identified and decoding
and playback are performed automatically in DTS, Dolby
Digital or PCM (2 channel stereo) format.
If no digital signal is being input, the analog input terminals are
selected.
Use this mode to play Dolby Digital signals.
DTS:
Decoding and playback are only performed when DTS signals
are being input.
PCM:
Decoding and playback are only performed when PCM signals
are being input.
ANALOG:
The signals input to the analog input terminals are played.
(This cannot be selected in the DVD mode.)
Different input modes can be selected for each input
function. The selected input mode is stored in the memory
for the individual input functions.
When the input function is set to something other than the
above, “ANALOG ONLY” is displayed and the input mode
cannot be selected.
The input mode automatically switches to “AUTO” if you
switch the input function to DVD from anything other than
DVD.
NORMAL (Factory default):
Make the selection when playing back in surround playback a
DVD that has been recorded with Dolby Digital or DTS on this
unit.
The Dolby Digital or DTS digital signal is also output from the
digital output terminals.
PCM:
DVDs that were recorded in Dolby Digital or DTS are
converted to linear PCM 48 kHz/16 bit (2 channels). Make the
selection when making a digital recording.
When “DIGITAL OUT” is selected:
Press the CURSOR
•
or
ª
button to select the
desired setting item, then press the ENTER
button.
3
-2
When playing Dolby Digital / DTS surround DVDs or 96 kHz
linear PCM DVDs on the S-101, be sure to set “DIGITAL
OUT” to “NORMAL” and “LPCM (44.1 kHz/48 kHz)” to
“OFF”.
When and only when you want to output the signals of the
Dolby Digital/DTS surround DVD being played on the S-101
to a digital PCM components, set “DIGITAL OUT” to
“PCM”.
With this setting, DVDs cannot be played on the S-101 in the
Dolby Digital / DTS surround mode. (The surround mode is
set to the mode in which PCM 2-channel signals can be
played.)
When and only when you want to make a digital recording
of the signals of a 48 kHz/20-bit/24-bit or 96 kHz linear PCM
DVD being played on the S-101 onto a digital recorder, set
the “LPCM (44.1 kHz/48 kHz)” to “ON”.
With this setting it is not possible to decode and play 48
kHz/20-bit/24-bit or 96 kHz linear PCM signals on the S-101
during recording. (Decoding and playback is in 48 kHz/16-bit
linear PCM format.)
When “LPCM (44.1 kHz/48 kHz)” is selected:
Press the CURSOR
•
or
ª
button to select the
desired setting item, then press the ENTER
button.
3
-3
ON:
DVDs that were recorded with linear PCM 48 kHz/20/24 bit
and 96 kHz modes are all converted to 48 kHz/16 bits. Make
this selection at the time of digital recording.
OFF (Factory default):
Make the selection when playing back to a decoder DVDs that
were recorded with this unit using linear PCM 48 kHz/20/24
bit and 96 kHz modes. Note that DVDs with Copyright
Protection are converted to 48 kHz/16 bits and played back.
The same signal is output from the digital output terminals.
