Bedienungsanleitung Denon X1800 Prime DJ (Seite 8 von 68) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

668293

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

42. FX Time: Turn this knob to select the rate that the BPM effect module will use. Press the knob

to switch between adjusting the rate as a time division and the rate in milliseconds. (A

corresponding light along the FX touch strip will illuminate to indicate the current time division.)

43. FX Touch Strip: When the Instant button is off (disabled), tap an area of this touch-

capacitive strip to select the time division that the BPM effect module will use. A

corresponding light along the strip will illuminate to indicate the current time division. If the

current time division is not a quantization value shown on the strip (e.g., the BeatBreak

effect), then none of the lights will illuminate.

When the Instant button is on (enabled), tap and hold your finger on the strip to activate

the effects, and then drag your finger up or down to adjust the time division of the effect.

44. Tap: Tap this button at least 3 times the desired tempo to set the rate of all time-based

effects. Press and hold this button for 1 second to set the tempo to that of FX Channel

Assign knob’s channel (e.g., if Channel 2 is using an effect with a rate of 135 BPM and the

FX Channel Assign knob is set to Channel 2, pressing and holding this button will set the

rate of time-based effects on all channels to 135 BPM).

45. FX Frequency: Turn this knob to select a frequency band of the audio signal to which the

BPM effects will be applied. Select the center (12:00) position to apply effects to the entire

spectrum of frequencies.

46. Utility: Press this button to enter or exit the Utility menu, which will appear in the display.

Exiting the Utility menu also saves any changes you made.

47. MIDI Send: Press this button to send a MIDI Start message out of the USB port or MIDI

output (you can use the Utility menu to select one). The tempo will be that of the selection

of the FX Channel Assign knob. If you change the selection of the FX Channel Assign

knob, press and hold this button to send the new tempo.

48. Engine Connect: When the Link ports are connected to SC5000 Prime units, press this

button to enable X1800 Prime to receive timing and BPM information (to synchronize

effect tempos) and to send track and user profile data between SC5000 Prime units.

49. USB Ports: Use standard USB cables to connect computers to these USB ports.

Rear Panel

10 10 10 10

3333

1. Power Input: Use the included power cable to connect this input to a power outlet.

2. Power Button: Press this button to power X1800 Prime on or off. Power on X1800Prime

only after you have connected all of your input devices and before you power on your

amplifiers and loudspeakers. Power off your amplifiers and loudspeakers before powering

off X1800 Prime.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denon X1800 Prime DJ Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info