Bedienungsanleitung Denver DCH-600 (Seite 5 von 6) (Englisch)

615538

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

To do an instant ip simply press the 360° Eversion button on the front of the controller,

the drone will ip forward 360°.

Warning: Do not perform a 360° ip unless the drone has enough space for safety.

Left Trigger

360° Eversion button

VIDEO AND CAMERA OPERATION

ENG-9 ENG-10

Camera

State LED

Micro-SD

Storage Card

Press the Mode button on lower right of the controller to switch between Flight

Mode 1 (maximum Gyro-stability) and Mode 2 (3D expert control). The LCD screen will

indicate the current mode.

Mode 1 automatically uses the 6-Axis Gyro (3 gyroscopes and 3 accelerometers) to its

full capabilities for stable, level ight. Use this mode for beginners, or to hover for

movies and snapshots.

Mode 2 tilts the drone more sharply (stronger pitch and roll), for faster acceleration.

Use this mode for racing and 3D maneuvers.

The drone can easily ip in an entire 360° circle. The drone will quickly stabilize and

level out, but will lose some altitude, so rst make sure the drone is ying high above

the ground.

To ip in the direction you choose, rst press the LEFT TRIGGER. The controller will

start beeping and enter 360° Flip Mode. Push the RIGHT STICK to ip in the desired

direction (forward, backward, left, or right) and return to normal ight. When the battery

runs low, the transmitter will activated a “di, di” sound alarm, the LED lights on the

drone will ash and the ip action will be auto turn off.

If the drone drifts to the side when

the stick is centered, click this switch

left or right until the drone is stable.

6. Adjust Left/Right Trim (Roll)

FLIGHT MODES

360° FLIPS

If the drone drifts forward or back

when the stick is centered, click this

switch forward or backward until

the drone is stable.

7. Adjust Forward/Backward Trim (Pitch)

1. If a storage card is not already installed, install a micro-SD ( “not included”) storage

card in the camera underneath the drone. See the small sketch on the camera itself,

which shows how to orient the chip correctly. Press the chip in until it clicks and stays.

2. To take a photograph, press the Camera Button on the front of the controller.The red

Camera State LED underneath the drone will blink on for about 2 seconds then off

indicating that the drone has taken a single, still photo.

3. To record video, press the Video Button on the front of the controller to start

recording. The red Camera State LED underneath the drone will come on to show

that video is being recorded. Press the Video Button against to stop recording.

Note: Always remember to stop the video recording with the controller before

shutting down. If the drone is switched off while still recording, the AVI le

being stored on the micro-SD card might not be “closed” or stored properly.

4. To quickly retrieve your videos and photos, connect the micro SD card reader

(included) to your computer. Optionally, you have remove the micro-SD storage card

and access the card directly with your computer. The data on the micro-SD card will

appear in folders as JPEG les and AVI les, which you can move to your computer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Denver DCH-600 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Denver DCH-600

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info