695743
6
Zoom out
Zoom in
Vorherige Seite
1/84
Nächste Seite
ENG-5
1. To store a preset, rst tune to your desired station, then press and hold the PRESET/MEMORY button on
the remote control, the display will show frequency and the “#” ash.
2. Press the PRESET ( UP or DOWN) button, until the display will show “ Preset Empty # ” and the “#” ash
to select your desired station preset number, then press the PRESET/MEMORY button on the remote
control to conrm your selection; the display will show “Preset # stored” in DAB/FM mode.
3. To recall a preset station, press the PRESET/MEMORY button once and then press the PRESET(UP or
DOWN) button to select the stations that you have stored, then press the PRESET/MEMORY button to
conrm your selection.
Note:
1. The stored stations will be saved into its memory and power off will not erase it. Storing a new station into
a preset location will erase the previously stored station in that location.
2. Turn on the unit and press and hold the MODE button until the display show” Press SELECT Key to
reset”, then press the SELECT/FM MONO/ST. button to erase all preset memory and the product in
standby mode.
LISTENING TO MUSIC OF A BLUETOOTH MOBILE PHONE OR
BLUETOOTH DEVICE
Pairing this system with a Bluetooth device
Pairing is an operation where Bluetooth devicesregister with each other beforehand. Use the
procedure below to pair the system with your Bluetooth device. Once a pairing operation is
performed, it does not need to be performed again.
Bluetooth pairing
1. Place the Bluetooth device to be connected to this system within
1 meter of the system.
2. Select the "Bluetooth”function.
3. Operate the Bluetooth device and perform the pairing operation.
For details about the operations of the Bluetooth device, refer
to the operation manual supplied with your Bluetooth device.
When searching for this system with the Bluetooth device, a list
of the devices found may appear in the Bluetooth device display
depending on the type of Bluetooth device. This system appears
as “DMS1702”. When establishing a connection with this system,
select the audio prole (A2DP, at the Bluetooth device. you may
require enter "8888" for the password (if your phone software
version is 2.1 or above is not require password) accept your
device's prompt until the display "BT LINK" is not ashing. The
connection is completed successfully.
BT LIN K
PASS 8888
6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Denver MDA-240 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info