Bedienungsanleitung DePaepe Progress (Seite 13 von 20) (Englisch, Französisch)

646678

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

EN 49/79

Installation

Base

1. Connect the modular end of the AC power adapter to the

power jack of the base, and then plug the AC adapters into

a standard AC wall outlet.

2. Connect one end of the phone line cord to the phone line

jack of the base, and the other end to a standard phone wall

outlet.

This terminal is designed to be connected to the main power 100/240V 50/60Hz through

a power adapter supplied with the unit and to the analog telephone network TNV3 as

defined in standard EN 60950 amendments 1 to 11.

EN 50/79

Handset

The rechargeable Ni-MH batteries (AAA size,

1.2V, 600mAh) come with your phone. Install

the batteries before use.

- Slide the battery cover in the direction of the

arrow and pull it out.

- Insert new batteries as indicated, matching correct polarity (+,-).

When replacing the batteries, always use good quality Ni-MH re-chargeable batteries.

Never use other batteries or conventional alkaline batteries.

Before initial operation, you should fully charge the handset for about 15 hours.

To charge the handset, you should place it on the base. When you place the handset on

the base, the handset automatically turns on.

To turn the handset on, press and hold the key until the display is switched on.

To turn off the handset, keep the

key pressed until the display disappears.

EN 51/79

Basic functions

 Making a Call

- Pick up the handset and press the key, the icon appears on LCD.

- Dial the telephone number.

- To end the call, press the

key.

Predialing: You can enter the desired phone number in standby mode, which allows you

to make corrections before dialing. Enter a telephone number (up to 32 digits). Check it.

You can also use the

key to insert a pause. When the number appears correctly,

press the

key.

 Receiving a call

When a call is received, the "New Call" information will appear on the LCD.

If the caller can be identified, the caller's phone number is displayed. If the caller cannot

be identified, only the "New Call" information displays.

EN 52/79

To answer the call, press the

key. If you have activated the Auto Answer function

(see page 72), when the handset is on the base, simply lift it up to answer.

Ringer volume: You can select the ringer volume by using the

or key when the

phone rings with an incoming call.

 Adjusting Voice Volume

During a conversation, you can use the or key to adjust the level of the earpiece

(or the handsfree speakerphone one, if activated) volume from V.1 to V.5. The selected

volume will be displayed on the LCD.

You can also select the earpiece volume or the speaker volume by the Audio Setup in

Menu under HS Settings, as described in page 69.

 Handsfree

During a call, you may turn on the speakerphone built in the handset. Press the

key, the

icon appears on the LCD. To turn the feature off, press the key again

and the

icon will disappear.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DePaepe Progress Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info