Bedienungsanleitung DeWalt D 21520 (Seite 24 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

78853

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

ENGLISH

Using an Extension Cable

If an extension cable is required, use an approved

extension cable suitable for the power input of this

machine (see technical data). The minimum

conductor size is 1.5 mm

. When using a cable reel,

always unwind the cable completely.

ASSEMBLY AND ADJUSTMENT

WARNING: Prior to assembly and

adjustment always unplug the tool.

Inserting and Removing a Bit (ﬁ g. A)

● Open the chuck by turning the sleeve (7)

counterclockwise and insert the bit shank.

● Put the chuck key (8) into each hole in the side

of the chuck and turn clockwise until tight.

● To remove the bit, proceed in reverse order.

Fitting the Side Handle (ﬁ g. A)

● Screw the side handle (5) into one of the

corresponding holes in the tool.

WARNING: Always use the side handle!

Fitting the Spade Handle (ﬁ g. A)

● Screw the spade handle (6) into the

corresponding hole on the back of the tool. Note

that the spade handle can be mounted in two

different positions.

WARNING: Use the spade handle

whenever possible.

Forward/reverse Slider (ﬁ g. C)

● To select forward or reverse rotation, use the

forward/reverse-switch (3) (see arrow on tool).

WARNING: Always wait until the motor

has come to a complete standstill before

changing the direction of rotation.

Chuck Removal (ﬁ g. B)

● Open the chuck jaws as far as possible.

● Insert an Allen key (12) into the chuck and

remove the chuck retaining screw (11) by turning

clockwise.

● Tighten an Allen key into the chuck and strike it

with a hammer as shown.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

Prior to Operation:

● Insert the appropriate bit.

● Mark the spot where the hole is to be drilled.

● Be aware of the location of pipework and wiring.

● Apply only a gentle pressure to the tool.

Excessive force does not speed up drilling but

decreases tool performance and may shorten

tool life.

Proper Hand Position (ﬁ g. A)

WARNING: To reduce the risk of

seriouspersonal injury, Always use

proper hand position as shown.

WARNING: To reduce the risk of serious

personal injury, ALWAYS hold securely

in anticipation of a sudden reaction.

Proper hand position requires one hand on the

side handle (5), with the other hand on the main

handle (9) or one hand on the spade handle (6)

with the other hand on the main handle (9).

Switching On and Off (ﬁ g. A)

● To run the tool, press the variable speed switch

(1). The pressure exerted on the variable speed

switch determines the tool speed.

● If necessary, press the lock-on button (2) for

continuous operation and release the switch.

The lock-on button works only in full speed,

forward rotation.

● To stop the tool, release the switch.

● To stop the tool in continuous operation, press the

switch brieﬂ y and release it. Always switch off the

tool when work is ﬁ nished and before unplugging.

● Always switch off the tool when work is ﬁ nished

and before unplugging.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D 21520 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info