Bedienungsanleitung DeWalt D 23550 (Seite 33 von 140) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

110214

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

ENGLISH

the motor reaction drives the unit rapidly back

toward the operator;

– If the blade becomes twisted or misaligned

in the cut, the teeth at the back edge of the

blade can dig into the top surface of the wood

causing the blade to climb out of the kerf and

jump back toward the operator.

Kickback is the result of saw misuse and/or incorrect

operating procedures or conditions and can be

avoided by taking proper precautions as given

below:

a) Maintain a firm grip with both hands on

the saw and position your arms to resist

kickback forces. Position your body to

either side of the blade, but not in line with

the blade. Kickback could cause the saw to

jump backwards, but kickback forces can be

controlled by the operator, if proper precautions

are taken.

b) When blade is binding, or when interrupting

a cut for any reason, release the trigger and

hold the saw motionless in the material until

the blade comes to a complete stop. Never

attempt to remove the saw from the work

or pull the saw backward while the blade is

in motion or kickback may occur. Investigate

and take corrective actions to eliminate the

cause of blade binding.

c) When restarting a saw in the work piece,

centre the saw blade in the kerf and check

that saw teeth are not engaged into the

material. If saw blade is binding, it may walk up

or kickback from the work piece as the saw is

restarted.

d) Support large panels to minimise the risk of

blade pinching and kickback. Large panels

tend to sag under their own weight. Supports

must be placed under the panel on both sides,

near the line of cut and near the edge of the

panel.

e) Do not use dull or damaged blades.

Unsharpened or improperly set blades produce

narrow kerf causing excessive friction, blade

binding and kickback.

f) Blade depth and bevel adjusting locking

levers must be tight and secure before

making cut. If blade adjustment shifts while

cutting, it may cause binding and kickback.

g) The D23550, D23650 has no plunge cutting

function!

Safety Instructions for Saws with a

Pendulum Blade Guard

a) Check lower guard for proper closing

before each use. Do not operate the saw if

lower guard does not move freely and close

instantly. Never clamp or tie the lower guard

into the open position. If saw is accidentally

dropped, lower guard may be bent. Raise

the lower guard with the retracting handle

and make sure it moves freely and does

not touch the blade or any other part, in all

angles and depths of cut.

b) Check the operation of the lower guard

spring. If the guard and the spring are not

operating properly, they must be serviced

before use. Lower guard may operate

sluggishly due to damaged parts, gummy

deposits, or a build-up of debris.

c) Lower guard should be retracted manually

only for special cuts such as “plunge

cuts” and “compound cuts”. Raise lower

guard by retracting handle and as soon as

blade enters the material, the lower guard

must be released. For all other sawing, the

lower guard should operate automatically.

d) Always observe that the lower guard is

covering the blade before placing saw

down on bench or floor. An unprotected,

coasting blade will cause the saw to walk

backwards, cutting whatever is in its path.

Be aware of the time it takes for the blade to

stop after switch is released.

Additional Safety Instructions for All

Saws with Riving Knife

a) Use the appropriate riving knife for the

blade being used. For the riving knife to

work, it must be thicker than the body of the

blade but thinner than the tooth set of the

blade.

b) Adjust the riving knife as described in

this instruction manual. Incorrect spacing,

positioning and alignment can make the riving

knife ineffective in preventing kickback.

c) Always use the riving knife except when

plunge cutting. Riving knife must be

replaced after plunge cutting. Riving knife

causes interference during plunge cutting

and can create kickback.

d) For the riving knife to work, it must be

engaged in the workpiece. The riving knife

is ineffective in preventing kickback during

short cuts.

e) Do not operate the saw if riving knife is

bent. Even a light interference can slow the

closing rate of a guard.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D 23550 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info