Bedienungsanleitung DeWalt d 25103 k (Seite 27 von 112) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

388762

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

ENGLISH

In this mode the tool can also be used as

a lever to free a jammed drill bit.

Bit rotation: non-working position used

only to rotate a flat chisel into the desired

position.

• To select the operating mode, press the safety

lock (5) and rotate the mode selector switch (4)

until it points to the symbol of the required mode.

• Release the safety lock and check that the mode

selector switch is locked in place.

Do not select the operating mode when

the tool is running.

Indexing the chisel position

The chisel can be indexed and locked into 51

different positions.

• Rotate the mode selector switch (4) until it points

to the “bit rotation” position.

• Rotate the chisel in the desired position.

• Set the mode selector switch (4) to the

“hammering only” position.

• Twist the chisel until it locks in position.

Inserting and removing SDS-plus

accessories

(fig. C)

This tool uses SDS-plus

accessories (refer to the

inset in fig. B for a cross-section of an SDS-plus

bit

shank).

We recommend to use professional accessories only.

• Clean and grease the bit shank.

• Insert the bit shank into the tool holder (6).

• Push the bit down and turn it slightly until it fits

into the slots.

• Pull on the bit to check if it is properly locked.

The hammering function requires the bit to be

able to move axially several centimetres when

locked in the tool holder.

• To remove a bit pull back the tool holder locking

sleeve (12) and pull out the bit.

Fitting the side handle (fig. D)

The side handle (10) can be fitted to suit both

RH- and LH-users.

Always use the tool with the side handle

properly assembled.

• Loosen the side handle.

• For RH-users, slide the side handle clamp over the

collar behind the tool holder, handle at the left.

• For LH-users, slide the side handle clamp over

the collar behind the tool holder, handle at the

right.

• Rotate the side handle to the desired position

and tighten the handle.

Setting the drilling depth (fig. E)

• Insert the required drill bit as described above.

• Press the depth stop clamp (11) and keep it

depressed.

• Fit the depth adjustment rod (9) through the hole

in the depth stop clamp.

• Adjust the drilling depth as shown.

• Release the depth stop clamp.

Forward/reverse slider (fig. F1 & F2)

D25102(K)/D25102C/D25103K/D25104K (fig. F1)

• Push the forward/reverse slider (3) to the RH-side

for forward (RH) rotation. See arrows on tool.

• Push the forward/reverse slider (3) to the LH-side

for reverse (LH) rotation.

D25203K (fig. F2)

• Push the forward/reverse slider (3) to the LH-side

for forward (RH) rotation. See arrows on tool.

• Push the forward/reverse slider (3) to the RH-side

for reverse (LH) rotation.

Always wait until the motor has come to

a complete standstill before changing the

direction of rotation.

D25102(K)/D25102C/D25103K/D25203K -

Fitting the chuck adapter & chuck

• Screw the chuck onto the threaded end of the

chuck adapter.

• Insert the connected chuck and adapter in the

tool as though it were a standard SDS-plus

bit.

• To remove the chuck, proceed as for removing a

standard SDS-plus

bit.

Never use standard chucks in the

hammer drilling mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt d 25103 k Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info