Bedienungsanleitung DeWalt d 25304 k (Seite 26 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

388880

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

Hammer drilling (fig. A)

Drilling with a solid bit

• Set the mode selector switch (3) to the «hammer

drilling» position.

• Insert the appropriate drill bit. For best results

use high quality carbide-tipped bits.

• Adjust the side handle (9) as required.

• If necessary, set the drilling depth.

• Mark the spot where the hole is to be drilled.

• Place the drill bit on the spot and switch on the

tool.

• Always switch off the tool when work is finished

and before unplugging.

Drilling with a core bit

• Set the mode selector (3) to the «hammer drilling»

position.

• Adjust the side handle (9) as required.

• Insert the appropriate core bit.

• Assemble the centerdrill into the core bit.

• Place the centerdrill on the spot and press the

variable speed switch (1). Drill until the core

penetrates into the concrete approx. 1 cm.

• Stop drilling and remove the centerdrill. Place the

core bit back into the hole and continue drilling.

• When drilling through a structure thicker than the

depth of the core bit, break away the round

cylinder of concrete or core inside the bit at

regular intervals. To avoid unwanted breaking

away of concrete around the hole, first drill a hole

the diameter of the centerdrill completely through

the structure. Then drill the cored hole halfway

from each side.

• Always switch off the tool when work is finished

and before unplugging.

Rotary drilling (fig. A)

• Set the mode selector switch (3) to the “rotary

drilling” position.

• Depending on your tool, follow either of the

following instructions:

- Fit the chuck adapter/chuck assembly

(D25303K).

- Replace the tool holder with the chuck

(D25304K).

• Proceed as described for hammer drilling.

Never use standard chucks in the

hammer drilling mode.

Screwdriving (fig. A)

• Set the mode selector switch (3) to the “rotary

drilling” position.

• Select the direction of rotation.

• Depending on your tool, follow either of the

following instructions:

- Insert the special SDS-plus

screwdriving

adaptor for use with hexagonal screwdriver bits

(D25303K).

- Replace the tool holder with the chuck

(D25304K).

• Insert the appropriate screwdriver bit.

When driving slotted head screws always use

bits with a finder sleeve.

• Gently press the variable speed switch (1) to

prevent damage to the screw head. In reverse

(LH) rotation the tool speed is automatically

reduced for easy screw removal.

• When the screw is flush with the workpiece,

release the variable speed switch to prevent the

screw head from penetrating into the workpiece.

Chipping and chiselling (fig. A)

• Set the mode selector switch (3) to the

«hammering only» position.

• Insert the appropriate chisel and rotate it by hand

to lock it into one of 51 positions.

• Adjust the side handle (9) as required.

• Switch on the tool and start working.

• Always switch off the tool when work is finished

and before unplugging.

• Do not use this tool to mix or pump

easily combustible or explosive fluids

(benzine, alcohol, etc.).

• Do not mix or stir inflammable liquids

labelled accordingly.

Various types of SDS-plus

drill bits and chisels are

available as an option.

Consult your dealer for further information on the

appropriate accessories.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt d 25304 k Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info