Bedienungsanleitung DeWalt D 25304 (Seite 25 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

78626

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

• Clean and grease the bit shank.

• Insert the bit shank into the tool holder (5).

• Push the bit down and turn it slightly until it fits

into the slots.

• Pull on the bit to check if it is properly locked.

The hammering function requires the bit to be

able to move axially several centimetres when

locked in the tool holder.

• To remove a bit pull back the tool holder locking

sleeve (11) and pull out the bit.

Fitting the side handle (fig. D)

The side handle (9) can be fitted to suit both

RH- and LH-users.

Always use the tool with the side handle

properly assembled.

• Loosen the side handle.

• For RH-users, slide the side handle clamp over the

collar behind the tool holder, handle at the left.

• For LH-users, slide the side handle clamp over the

collar behind the tool holder, handle at the right.

• Rotate the side handle to the desired position

and tighten the handle.

Setting the drilling depth (fig. E)

• Insert the required drill bit as described above.

• Press the depth stop clamp (10) and keep it

depressed.

• Fit the depth adjustment rod (8) through the hole

in the depth stop clamp.

• Adjust the drilling depth as shown.

• Release the depth stop clamp.

Forward/reverse slider (fig. A)

• Push the forward/reverse slider (2) to the LH-side

for forward (RH) rotation. See arrows on tool.

• Push the forward/reverse slider (2) to the RH-side

for reverse (LH) rotation.

Always wait until the motor has come to

a complete standstill before changing the

direction of rotation.

D25303K - Fitting the chuck adapter & chuck

• Screw the chuck onto the threaded end of the

chuck adapter.

• Insert the connected chuck and adapter in the

tool as though it were a standard SDS-plus® bit.

• To remove the chuck, proceed as for removing a

standard SDS-plus® bit.

Never use standard chucks in the

hammer drilling mode.

D25304K - Replacing the tool holder with

the chuck (fig. F)

• Turn the locking collar (7) into the unlocking

position and pull the tool holder (5) off.

• Push the chuck (12) onto the spindle and turn the

locking collar into the locking position.

• To replace the chuck with the tool holder, first

remove the chuck the same way as the tool

holder was removed. Then place the tool holder

the same way as the chuck was placed.

Never use standard chucks in the

hammer drilling mode.

Replacing the dust cover (fig. B)

The dust cover (6) prevents dust ingress into the

mechanism. Replace a worn dust cover immediately.

• Pull back the tool holder locking sleeve (11) and

pull the dust cover (6) off.

• Fit the new dust cover.

• Release the tool holder locking sleeve.

Instructions for use

Always observe the safety instructions

and applicable regulations.

Be aware of the location of pipework and wiring.

Apply only a gentle pressure to the tool (approx. 5 kg).

Excessive force does not speed up drilling but

decreases tool performance and may shorten tool life.

Do not drill or drive too deep to prevent damage to

the dust cover.

Switching on and off (fig. A)

• To run the tool, press the variable speed switch

(1). The pressure exerted on the variable speed

switch determines the tool speed.

• To stop the tool, release the switch.

• To lock the tool in off position, move the forward/

reverse slider (2) to the central position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D 25304 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info