Bedienungsanleitung DeWalt d 25701 k (Seite 29 von 136) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

388950

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

ENGLISH

Service Indicator LEDs (ﬁ g. 2)

The yellow brushwear indicator LED (e) lights up

when the carbon brushes are nearly worn out to

indicate that the tool needs servicing within the next

8 hours of use. The red service indicator LED (d)

lights up if there is a fault with the tool or the brushes

have completely worn out (refer to Brushes under

Maintenance).

Fully Vibration-dampened Main

Handle (ﬁ g. 1)

The dampers in the main handle (m) absorb the

vibrations transmitted to the user. This improves user

comfort during the operation.

Active Vibration Control

D25701, D25730

The active vibration control neutralises rebound

vibration from the hammer mechanism. Lowering

hand and arm vibration, it allows more comfortable

use for longer periods of time and extends the life of

the unit.

Electrical Safety

The electric motor has been designed for one

voltage only. Always check that the power supply

corresponds to the voltage on the rating plate.

Your DEWALT tool is double insulated in

accordance with EN 60745; therefore no

earth wire is required.

WARNING: 115 V units have to

be operated via a fail-safe isolating

transformer with an earth screen

between the primary and secondary

winding.

If the supply cord is damaged, it must be replaced

by a specially prepared cord available through the

EWALT service organisation.

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in

the plug.

• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be

made to the earth terminal.

Follow the fitting instructions supplied with good

quality plugs. Recommended fuse: 13 A.

Using an Extension Cable

An extension cord should not be used unless

absolutely necessary. Use an approved extension

cable suitable for the power input of this tool

(see technical data). The minimum conductor size is

1 mm

; the maximum length is 30 m.

When using a cable reel, always unwind the cable

completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-ups

or when making repairs. Be sure the

trigger switch is in the OFF position. An

accidental start-up can cause injury.

Inserting and Removing SDS Max

Accessories (ﬁ g. 3A, 3B)

This machine uses SDS Max

drill bits and chisels

(refer to the inset in figure 3B for a cross-section of

an SDS Max

bit shank).

1. Clean and grease the bit shank.

WARNING: Only apply a slight amount

of lubricant to the bit shank. Do not

apply lubricant to the machine.

2. Insert the bit shank into the tool holder (h),

and press and turn the bit slightly until the

sleeve snaps into position.

3. Pull on the bit to check if it is properly locked.

The hammering function requires the bit to be

able to move axially several centimetres when

locked in the tool holder.

4. To remove a bit pull back the tool holder locking

sleeve (h) and pull the bit out of the tool holder.

Selecting the Operating Mode

(ﬁ g. 4A, 4B)

The tool can be used in two operating modes (fig. 4A):

Hammerdrilling: for concrete, brick,

stone and masonry drilling operations.

Hammering only: for chiselling and

demolition applications. In this mode the

tool can also be used as a lever to free a

jammed drill bit.

1. To select the operating mode, rotate the mode

selector switch (g) until it points to the symbol of

the required mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt d 25701 k Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info