Bedienungsanleitung DeWalt D 25701 (Seite 30 von 136) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

78767

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

ENGLISH

It may be neccessary to twist the tool holder (h)

slightly to allow the mode selector switch (g) to

pass the “0” position.

2. Check that the mode selector switch (g) is

locked in place.

Indexing the Chisel Position

(ﬁ g. 4A, 4B)

The chisel can be indexed and locked into 24

different positions (fig. 4B).

1. Rotate the mode selector switch (g) until it

points towards the “0” position.

2. Rotate the chisel in the desired position.

3. Set the mode selector switch (g) to the

“hammering only” position.

4. Twist the chisel until it locks in position.

Setting the Electronic Speed and

Impact Control Dial (ﬁ g. 2)

Turn the dial (c) to the desired level. Turn the dial

upwards for higher speed and downwards for

lower speed. The required setting is a matter of

experience. E.g.:

– when chiselling or drilling in soft, brittle materials

or when minimum break-out is required, set the

dial to a low setting;

– when breaking or drilling in harder materials, set

the dial to a high setting.

Setting the Torque Control Switch

(ﬁ g. 2)

D25701/D25730

The tool selects low torque position automatically

every time the tool is plugged in.

1. To select high torque, slide the torque control

switch (f) to the right until it locks into place.

2. To select low torque, slide the torque control

switch (f) to the left until it locks into place.

3. It may be neccessary to twist the tool holder

slightly to allow the mechanism to engage.

Assembling and Fitting the Side

Handle (ﬁ g. 5A–5C)

The side handle (j) can be mounted in front or in rear

position on either side of the machine to suit both

RH- and LH-users.

WARNING: Always operate the

tool with the side handle properly

assembled.

MOUNTING IN FRONT POSITION (FIG. 5A, 5B)

1. Snap the steel ring (q) over the collar (i) behind

the tool holder (h). Squeeze both ends together,

mount the bush (o) and insert the pin (p).

2. Place the side handle clamp (n) and screw on

the clamp wheel (k). Do not tighten.

WARNING: Once assembled, the side

handle clamp should never be removed.

3. Screw the side handle (j) into the clamp wheel

and tighten it.

4. Rotate the side handle mounting assembly to

the desired position. For drilling horizontally

with a heavy drill bit, we recommend to place

the side handle at an angle of approx. 20° for

optimum control (fig. 5B).

5. Lock the side handle mounting assembly in

place by tightening the clamp wheel (k).

MOUNTING IN REAR POSITION (FIG. 5C)

The rear position is particularly useful when drilling

down into a floor.

1. Unscrew the side handle (j) and remove it

from the front position. Leave the side handle

mounting assembly in front position.

2. Screw the side handle directly into one of the

rear side handle positions (l) on either side of the

tool.

OPERATION

Instructions for Use

WARNING:

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework

and wiring.

• Apply only a gentle pressure to

the tool (approx. 20 kg). Excessive

force does not speed up drilling but

decreases tool performance and may

shorten tool life.

• Always hold the tool ﬁrmly with both

hands and ensure a secure stance.

Always operate the tool with the side

handle properly assembled.

Proper Hand Position (ﬁ g. 1, 6)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D 25701 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info