Bedienungsanleitung DeWalt D 26422 (Seite 29 von 116) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

78610

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

ENGLISH

WARNING: Do not use a dustbag or

vacuum extractor without proper spark

protection when sanding metal.

1. Fit the dustbag (8) into the frame (7) as shown.

2. Attach the frame (7) to the dust extraction

outlet (14).

3. Turn the assembly clockwise to lock it in position.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories.

WARNING:

• Make sure all materials to be sanded

are well secured.

• Apply only a gentle pressure to the

workpiece. Excessive pressure does

not improve the sanding effect, but

only results in an increased load on

the machine and causes the abrasive

to tear.

• Avoid overloading.

WARNING: Do not sand magnesium!

Proper Hand Position (ﬁ g. F)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the front

handle (4), with the other hand on the main handle

(18).

Switching On and Off (ﬁ g. A)

• Switching on: press the on/off switch (1).

• For continuous operation, also press the lock-

on button (2).

• Switching off: press the on/off switch again.

Sanding (ﬁ g. A)

• Start with the coarsest grit size.

• As the tool produces small scratch marks in all

directions, it is not necessary to sand with the

grain.

• Check your work at short intervals.

• Always switch off the tool when work is finished

and before unplugging.

Replacing the Dustbag (ﬁ g. E)

For efficient dust extraction replace the dustbag

when it is about one third full.

1 . Carefully pull the dustbag opening (15) off the

frame outlet (16) and remove the dustbag (8).

2. Fit a new dustbag following the instructions as

described above.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-

ups or when making repairs. Be sure

the trigger switch is in the OFF position.

An accidental start-up can cause injury.

Lubrication

Your power tool requires no additional lubrication.

• After the tool is used in metal sanding

applications without dustbag, clean the tool

using low-pressure air.

Cleaning

WARNING: Blow dirt and dust out of

the main housing with dry air as often as

dirt is seen collecting in and around the

air vents. Wear approved eye protection

and approved dust mask when

performing this procedure.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D 26422 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt D 26422

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info