Bedienungsanleitung DeWalt D 26480 (Seite 27 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

78283

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

ENGLISH

When using a cable reel, always unwind the cable

completely.

ASSEMBLY AND ADJUSTMENT

WARNING: Prior to assembly and

adjustment always unplug the tool.

Fitting and Centring the Sanding Belt

(ﬁ g. 1)

The tool uses 64 x 356 mm sanding belts.

1. Turn the belt tensioning lever (d) clockwise until

it is in the release position.

2. Remove the sanding belt (f).

3. Place a new sanding belt making sure that the

arrow on the inside of the sanding belt points

in the same direction as the arrow on the

machine.

Sanding belts without arrows can go either

direction. If the belt is monodirectional and has

arrows printed on its inside, make sure to point

these arrows in the direction of belt rotation

indicated on the sander.

(Belt rotation would be

clockwise when looking into the open side of the

sander)

4. Turn the belt tensioning lever counterclockwise

until it is in the clamp position.

5. Switch the machine on and turn the belt

centring knob (e) until the sanding belt is

centred on the front roller (c).

Front Handle (ﬁ g. 1)

The front handle is removeable to allow the sander

into tight spaces. The unit comes with the handle

(b) installed as shown. To remove the handle,

loosen the flat/torx head screw (g) in the centre of

the handle using a flat head screwdriver and then

remove front handle and flat/torx head screw.

NOTE: The front handle must be properly seated

over the mounting surface before tightening the

screw.

Tracking the Belt (ﬁ g. 1, 2)

WARNING: Severe laceration hazard.

Properly adjust the tracking of the belt

to avoid it overhanging the housing. A

running belt overhanging the housing

can cause severe lacerations.

To ensure the sanding belt is tracking properly on

your unit:

1. Grasp unit in your hand and hold with the belt

facing you.

2. Turn on switch (a) to start the belt sander.

3. Turn the tracking knob (e) counterclockwise

(turning towards the front of the sander) to

move the belt toward the housing. Turn the

knob clockwise (towards the power cord) to

move it away from the housing.

NOTE: The belt should be aligned with the flush

edge of the platen (i) while the sander is in operation.

4. Turn switch off and make sure the belt has come

to a complete stop before setting unit down.

Dust Extraction (ﬁ g. 3)

WARNING: Empty dust collection

system frequently, especially when

sanding resin-coated surfaces such

as polyurethane, varnish, shellac,

etc. Dispose of coated dust particles

according to the finish manufacturer’s

guidelines, or place in a metal can with

a tight fitting metal lid. Remove coated

dust particles from the premises daily.

The accumulation of fine sanding dust

particles may self ignite and cause fire.

WARNING: Shock hazard. The use of

a vacuum hose and vacuum adaptor

with the belt sander may generate static

electricity that could result in startling

static discharge.

WARNING: Do not use a dustbag or

vacuum extractor without proper spark

protection when sanding metal. Doing

so creates a fire hazard, which may

cause serious personal injury and/or

damage to the tool.

Your belt sander is equipped with a dual hose

adaptor. The various diameters of the dust extraction

adaptor can be attached to vacuum nozzles of 20,

25–27 and 35–38 mm diameters for dust collection.

Insert the adaptor (j) into the dust port (k) and turn

it 1/8 turn clockwise to secure the adaptor to the

sander. Then, attach the appropriate vacuum hose

to the adaptor.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D 26480 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info