Bedienungsanleitung DeWalt D 28400 (Seite 37 von 174) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

79089

Zoom out

Zoom in

Vorherige Seite

1/174

Nächste Seite

ENGLISH

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories. Before

reconnecting the tool, depress and

release the trigger switch to ensure that

the tool is off.

Attaching Side Handle (ﬁ g. 5, 6)

WARNING: Before using the tool,

check that the handle is tightened

securely.

For grinding, screw the side handle (e) tightly into

one of the holes (r) on either side of the gear case

(fig. 5).

For cutting, screw the side handle (e) tightly into the

top hole (s) or into one of the holes (t) on either side

of the gear case (fig. 6).

Fitting a Wire Cup Brush

Screw the wire cup brush directly onto the spindle

without the use of the spacer and threaded ﬂ ange.

Mounting and Removing the Guard

(ﬁ g. 2)

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories. Before

reconnecting the tool, depress and

release the trigger switch to ensure that

the tool is off.

CAUTION: Guards must be used with

this grinder.

When using the D28400 or the D28401 grinder for

cutting metal or masonry a Type 1 guard MUST be

used. Type 1 guards are available at extra cost from

DEWALT distributors.

NOTE: Please refer to the Grinding and Cutting

Accessory Chart at the end of this section to

show other accessories that can be used with these

grinders.

1. Place the angle grinder on a table, spindle (o)

up.

2. Release the clamping lock (f) and hold the guard

(d) over the tool as shown.

3. Align the lugs (k) with the notches (l).

4. Press the guard (d) down and rotate it to the

required position.

5. Fully close the clamping lock (f)

6. Ensure screw (m) is fastened tightly and the

guard is fixed

7. To remove the guard, reverse the above

instructions.

CAUTION: If the guard cannot be

tightened by the adjusting screw, do

not use the tool. To reduce the risk of

personal injury, take the tool and guard

to a service center to repair or replace

the guard.

Fitting and Removing a Grinding or

Cutting Disc (ﬁ g. 1, 3, 4)

WARNING: Do not use a damaged

disc.

1. Place the tool on a table, guard up.

2. Fit the backing flange (i) correctly onto the

spindle (o) (fig. 3).

3. Place the disc (n) on the backing flange (i).

When fitting a disc with a raised center, make

sure that the raised centre (j) is facing the

backing flange (i).

4. Screw the threaded clamp nut (h) onto the

spindle (o) (fig. 4):

a. The ring on the threaded clamp nut (h) must

face towards the disc when fitting a grinding

disc (fig. 4A);

b. The ring on the threaded clamp nut (h) must

face away from the disc when fitting a cutting

disc (fig. 4B).

5. Press the spindle lock button (c) and rotate the

spindle (o) until it locks in position.

6. Tighten the threaded clamp nut (h) with the two-

pin spanner supplied.

7. Release the spindle lock.

8. To remove the disc, loosen the threaded clamp

nut (h) with the two-pin spanner.

Prior to Operation

• Install the guard and appropriate disc or wheel.

Do not use excessively worn discs or wheels.

• Be sure the inner and outer flange are mounted

correctly.

• Make sure the disc or wheel rotates in the

direction of the arrows on the accessory and the

tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D 28400 Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info