Bedienungsanleitung DeWalt D 28422 (Seite 26 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

79090

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

ENGLISH

• Release the spindle lock.

• To remove the disc, loosen the flange (14) with

the two-pin spanner.

Do not use a damaged disc.

Fitting a wire cup brush

• Screw the wire cup brush directly onto the

spindle without the use of the spacer and

threaded flange.

Mounting the side handle (fig. D1 & D2)

• For grinding, screw the side handle (5) tightly into

one of the holes (15) on either side of the gear

case (fig. D1).

• For cutting, screw the side handle (5) tightly into

the top hole (16) or into one of the holes (17) on

either side of the gear case (fig. D2).

D28423/D28432C - Rotating the main handle

(fig. E1 & E2)

The rotary handle facilitates a more comfortable

handling in cutting applications with the side handle

mounted in the top hole.

The rotary handle has locations at 30°, 60° and 90°

both left and right.

• Pull the spring-loaded tab (18) to unlock the

rotary mechanism (fig. E1). Hold the tab in the

pulled-out position.

• Rotate the handle (19) into the desired position

(fig. E2).

• Release the tab and lock it in position.

• Check that the rotary mechanism is locked.

Do not use the tool unless the rotary

handle is in the locked postion.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Ensure all materials to be ground or cut

are secured in place.

• Apply only a gentle pressure to the tool.

Do not exert side pressure on the disc.

• Avoid overloading. Should the tool

become hot, let it run a few minutes

under no load condition.

Prior to operation:

• Install the guard and appropriate disc or wheel.

Do not use excessively worn discs or wheels.

• Be sure the inner and outer flange are mounted

correctly.

• Make sure the disc or wheel rotates in the direction

of the arrows on the accessory and the tool.

Switching on and off (fig. A)

The on/off switch is equipped with an unlocking

switch or a locking switch for continuous operation.

On/off switch (1) with locking switch (2)

• To run the tool, depress the locking switch (2)

and subsequently operate the on/off switch (1).

• Release the locking switch (2).

• To stop the tool, press the on/off switch again.

On/off switch (1) with unlocking switch (2)

(France only)

• To run the tool, depress the unlocking switch (2)

and subsequently operate the on/off switch (1).

• Release the unlocking switch (2).

• To stop the tool, release the switch.

Do not switch the tool on or off when

under load.

Consult your dealer for further information on the

appropriate accessories.

Maintenance

Your DEWALT Power Tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

Keep the ventilation slots clear and regularly clean

the housing with a soft cloth.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D 28422 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt D 28422

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info