Bedienungsanleitung DeWalt D 28432 (Seite 41 von 192) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

79080

Zoom out

Zoom in

Vorherige Seite

1/192

Nächste Seite

ENGLISH

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in

the plug.

• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be

made to the earth terminal.

Follow the fitting instructions supplied with good

quality plugs. Recommended fuse: 13 A.

Using an Extension Cable

If an extension cable is required, use an approved

extension cable suitable for the power input of this

tool (see technical data). The minimum conductor

size is 1 mm

; the maximum length is 30 m.

When using a cable reel, always unwind the cable

completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories. Before

reconnecting the tool, depress and

release the trigger switch to ensure that

the tool is off.

Attaching Side Handle (ﬁ g. 6, 7)

WARNING: Before using the tool,

check that the handle is tightened

securely.

For grinding, screw the side handle (e) tightly into

one of the holes (o) on either side of the gear case

(fig. 6).

For cutting, screw the side handle (e) tightly into the

top hole (p) or into one of the holes (q) on either side

of the gear case (fig. 7).

Fitting a Wire Cup Brush

Screw the wire cup brush directly onto the spindle

without the use of the spacer and threaded flange.

Rotating the Main Handle (ﬁ g. 8, 9)

D28423, D28432C, D28750

The rotary handle facilitates a more comfortable

handling in cutting applications with the side handle

mounted in the top hole.

The rotary handle has locations at 30°, 60° and 90°

both left and right.

1. Pull the spring-loaded tab (r) to unlock the rotary

mechanism (fig. 8). Hold the tab in the pulled-

out position.

2. Rotate the handle (s) into the desired position

(fig. 9).

3. Release the tab and lock it in position.

4. Check that the rotary mechanism is locked.

WARNING: Do not use the tool unless

rotary handle is in the locked position.

Mounting and Removing the Guard

(ﬁ g. 2)

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories. Before

reconnecting the tool, depress and

release the trigger switch to ensure that

the tool is off.

CAUTION: Guards must be used with

this grinder.

When using the D28410, D28411, D28413,

D28414, D28421, D28422, D28423, D28432C or

the D28750 grinder for cutting metal or masonry

a Type 1 guard MUST be used. Type 1 guards are

available at extra cost from DEWALT distributors.

NOTE: Please refer to the Grinding and Cutting

Accessory Chart at the end of this section to

show other accessories that can be used with these

grinders.

1. Place the angle grinder on a table, spindle up.

2. Release the clamping lock (f) and hold the guard

(d) over the tool as shown.

3. Align the lugs (g) with the notches (h).

4. Press the guard down and rotate it to the

required posiiton.

5. If required, increase the clamping force by

tightening the screw (i).

6. Tighten the clamping lock.

To remove the guard, release the clamping lock.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D 28432 Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt D 28432

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info