Bedienungsanleitung DeWalt D21441 T 2 (Seite 27 von 116) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544697

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

ENGLISH

● Fit the depth adjustment rod (6) through the

hole in the side handle clamp.

● Adjust the drilling depth as shown.

● Tighten the side handle.

Forward/reverse Slider (ﬁ g. A)

● To select forward or reverse rotation, use the

forward/reverse-switch (3) (see arrow on tool).

WARNING: Always wait until the

motor has come to a complete

standstill before changing the direction

of rotation.

Two Gear Selector (ﬁ g. D)

Your tool is ﬁ tted with a two gear selector (4) to

vary the speed/torque ratio.

● Release the variable speed switch and select

the required position. This can be done either

with the tool switched off or running under no

load condition. Always align the selector with

the arrow on the gear housing:

1 low speed/high torque

(drilling large holes, driving large screws)

2 high speed/low torque

(drilling smaller holes, drilling in wood)

For speed rates, refer to the technical data.

● Do not change gears at full speed or during

use.

Chuck Removal (ﬁ g. E & F)

● Open the chuck jaws as far as possible.

● Insert a screwdriver into the chuck and remove

the chuck retaining screw (10) by turning

clockwise.

● Tighten an Allen key into the chuck and strike

it with a hammer as shown.

Prior to Operation

● Insert the appropriate bit.

● Mark the spot where the hole is to be drilled.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories.

●

Be aware of the location of pipework

and wiring.

● Apply only a gentle pressure to the

tool. Excessive force does not speed

up drilling but decreases tool

performance and may shorten tool life.

Proper Hand Position (ﬁ g. C)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the side

handle (5), with the other hand on the main handle

(9).

Switching On and Off (ﬁ g. A)

● To run the tool, press the variable speed

switch (1). The pressure exerted on the

variable speed switch determines the tool

speed.

● If necessary, press the lock-on button (2) for

continuous operation and release the switch.

The lock-on button works only in full speed,

forward rotation.

● To stop the tool, release the switch.

● To stop the tool in continuous operation, press

the switch brieﬂ y and release it. Always switch

off the tool when work is ﬁ nished and before

unplugging.

Rotary Drilling (ﬁ g. A)

● Press the switch (1).

Screwdriving

● Select forward or reverse rotation.

● Press the switch (1).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D21441 T 2 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info