Bedienungsanleitung DeWalt D21441 (Seite 24 von 104) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

500447

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

ENGLISH

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in the

plug.

• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be made

to the earth terminal.

Follow the fitting instructions supplied with good

quality plugs. Recommended fuse: 13 A.

Using an extension cable

If an extension cable is required, use an approved

extension cable suitable for the power input of this

machine (see technical data). The minimum

conductor size is 1.5 mm

. When using a cable

reel, always unwind the cable completely.

Assembly and adjustment

WARNING: Prior to assembly and

adjustment always unplug the tool.

Inserting and removing a bit (ﬁ g. A)

● Open the chuck by turning the sleeve (8)

counterclockwise and insert the bit shank.

● Place the bit in the chuck as far as it will go and

lift slightly before tightening.

● Tighten ﬁ rmly by turning the sleeve clockwise.

● To remove the bit, proceed in reverse order.

Fitting the side handle (ﬁ g. A)

The side handle (5) can be ﬁ tted to suit both RH-

and LH-users.

WARNING: Always use the drill with the

side handle properly assembled.

● Loosen the side handle.

● For RH-users, slide the side handle clamp over

the collar behind the chuck, handle at the left.

● For LH-users, slide the side handle clamp over

the colar behind the chuck, handle at the right.

● Rotate the side handle to the desired position

and tighten the handle.

Setting the drilling depth (ﬁ g. B)

● Insert the required drill bit into the chuck.

● Slacken the side handle (5).

● Fit the depth adjustment rod (6) through the

hole in the side handle clamp.

● Adjust the drilling depth as shown.

● Tighten the side handle.

Forward/reverse slider (ﬁ g. A)

● To select forward or reverse rotation, use the

forward/reverse-switch (3) (see arrow on tool).

WARNING: Always wait until the motor

has come to a complete standstill

before changing the direction of

rotation.

Two gear selector (ﬁ g. C)

Your tool is ﬁ tted with a two gear selector (4) to

vary the speed/torque ratio.

● Release the variable speed switch and select

the required position. This can be done either

with the tool switched off or running under no

load condition. Always align the selector with

the arrow on the gear housing:

1 low speed/high torque

(drilling large holes, driving large screws)

2 high speed/low torque

(drilling smaller holes, drilling in wood)

For speed rates, refer to the technical data.

● Do not change gears at full speed or during use.

Chuck removal (ﬁ g. D & E)

● Open the chuck jaws as far as possible.

● Insert a screwdriver into the chuck and remove

the chuck retaining screw (9) by turning

clockwise.

● Tighten an Allen key into the chuck and strike it

with a hammer as shown.

Instructions for use

WARNING:

● Always observe the safety instructions

and applicable regulations.

● Be aware of the location of pipework

and wiring.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D21441 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info