Bedienungsanleitung DeWalt D21583K T-2 (Seite 33 von 156) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

591334

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

ENGLISH

• After interrupting the cut, do not switch on

until the core bit can rotate freely.

• Always trigger off the switch to prevent the

machine from accidentally self starting.

Note this procedure especially after the

power supply is interrupted or the plug is

disconnected from the power outlet.

• Mounting the tool onto a stand is

recommended to increase the user comfort

and reduce the risk of injuries.

• In case of jammed core bit disconnect the

machine from the power supply, remove

the reason for the jam before turning on the

machine again.

DRY DRILLING

• Dry drilling is suitable for masonry

(bricks, breeze blocks).

• Always use a suitable dust extractor.

• Always use core bits designed for dry drilling.

• Do not use the machine handheld with core

bits larger than 100 mm.

• Always mount the drill on a stand when

drilling holes larger than 100 mm.

• Wear a dust mask when performing dry cuts.

D21583 - WET DRILLING

• Wet drilling is suitable for stone and concrete.

• Always use a water cooling device and a

water collection system.

• Always use core bits designed for wet drilling.

• The maximum water pressure is 3 bar. Use

a pressure relieve valve in case of a higher

water pressure.

• Use only pure tap water for cooling

purposes.

• Prevent water from entering the motor or

other electrical components. Make sure the

PRCD is not in contact with water.

Safe Operation for Stationary Stands

• A machine incorrectly assembled may

cause a hazardous situation. Carefully fix the

machine into the drill stand and check that

the drill stand holder is secured.

• Fixing the drill stand with vacuum device can

lead to dangerous situations.

• Check the surface where the drill stand shall

be fixed. surface such as irregular (rough) can

significantly reduce the effectiveness of the

suction system. Coated or laminated surface

can be pulled off during work.

• The minimum vacuum level shall not be lower

than 600mbar. Periodically control this value

on the pressure gauge.

• Do not use drill core bits with a diameter

greater than 202 mm at this application.

5) SERVICE

a) Have your power tool serviced by a

qualified repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

Additional Speciﬁ c Safety Rules for

Diamond Drills

• Wear ear protectors. Exposure to noise can

cause hearing loss.

• Hold power tools by insulated gripping

surfaces when performing an operation

where the cutting tool may contact hidden

wiring or its own cord. Cutting accessory

contacting a “live” wire may make exposed

metal parts of the tool “live” and shock the

operator.

• Use auxiliary handles supplied with the

tool. Loss of control can cause personal

injury.

• Wear safety goggles or other eye

protection. Drilling operations cause chips to

fly. Flying particles can cause permanent eye

damage.

• Bits, tools and drilling area get hot during

operation. Wear gloves when touching

them.

• Use the diamond drill under constant

supervision.

• Make sure not to cut through electric mains,

gas or water pipes. Use detection systems

prior to drilling.

• Make sure the cutting accessory is fitted

properly.

• Check all screws and tighten securely before

you use the machine.

• When drilling downward, make sure the core

can drop safely without injuring someone

standing beneath.

• Do not perform overhead (upward) drilling

without the use of suitable protection

shielding (water collecting device).

• When drilling handheld, always use the side

handle and hold the machine firmly with both

hands.

• Make sure to stand on a stable surface and

keep body balance at all times for better

control of reaction torque.

• Inspect the machine before every use. Do not

use the machine if there are any defectives

on the mains plug, power cord, trigger switch

or any part of the housing. Have the machine

repaired by an authorized repair agent.

• Do not use the machine in a damp or wet

location.

• Switch off the machine immediately if there is

any leak of water.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D21583K T-2 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info