Bedienungsanleitung DeWalt D215851 (Seite 27 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544691

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

E N G L I S H

● Turn the stabilizer bolts (15) one by one until

the stand is level

Mounting the water collection ring (ﬁg. H)

If the stand is used in wet drilling applications,

a water collection ring can be mounted to ensure

a proper discharge of water.

● Loosen the bolts (46) a few turns.

● Hold the water collection ring (26) in front of the

base (9).

● Slide the recessed ends of the mounting

bracket (47) in the space created between the

bolts and the base.

● Check that the assembly aligns with the

accessory ﬁtted.

● Securely tighten the bolts.

Adjusting the drill angle (ﬁg. I)

The column can be tilted to facilitate slope drilling

applications. The scale (7) represents angles up to

45°.

● Remove the locking bolt (48) and store it in

a safe place.

● Loosen the angle adjustment lever (8).

● Tilt the column at the handle (3).

● Align the top of the lever base with the required

angle (see indication X).

● Tighten the angle adjustment lever.

● After use, restore the stand in straight-up

position and replace the locking bolt.

Fitting the feed handle (ﬁg. J)

The quick-release feed handle (4) can be mounted

in one simple operation both to the left and the

right of the stand.

● Align the locating rod in the feed handle with

the slot in the shaft (49).

● Push the handle onto the shaft.

Adjusting the friction (ﬁg. A)

The friction knob (13) is used to increase or

decrease the friction of the carriage mechanism.

● Turn the knob clockwise to increase the friction.

● Turn the knob counterclockwise to decrease the

friction.

Instructions for use

Always observe the safety instructions

and applicable regulations.

Also refer to your drill manual.

Prior to operation:

● Make sure the stand is fastened securely.

● Mount the appropriate accessory.

● Check the friction on the carriage.

● Mark the spot where the hole is to be drilled.

Unlocking the carriage (ﬁg. K)

● To unlock the carriage (1) pull out the lock knob

(2).

● To lock the carriage move the carriage until the

locking shaft passes the hole (50) in the column

and jumps into place.

Always lock the carriage when the

assembly is not in use.

General tips for drilling with diamond core bits

Follow the core bit or manufacturer's

recommendations for using the

accessory.

Note: The use of a centredrill is not necessary.

● Take hold of the feed handle.

● Unlock the carriage.

● Switch on the drill motor in continuous mode.

● Slowly feed the accessory into the workpiece

using the feed handle.

● At the start of the cut, apply light pressure to

allow the accessory to perform the initial groove.

● Continue applying sufﬁcient pressure to achieve

a smooth progressive cut. Do not force.

● Take extra care when the accessory is about to

break through the surface to prevent splintering.

● Always switch off the tool when work is ﬁnished

and before unplugging.

● After use move the carriage upwards until the

carriage locks into place.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D215851 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info