Bedienungsanleitung DeWalt D21717 T 2 (Seite 28 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

544704

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

2. Always apply pressure in a straight line with the

bit. Use enough pressure to keep drill biting, but

do not push hard enough to stall the motor or

deflect the bit.

3. Hold tool firmly with both hands to control the

twisting action of the drill.

CAUTION: Drill may stall if overloaded

causing a sudden twist. Always expect

the stall. Grip the drill firmly to control the

twisting action and avoid injury.

4. IF DRILL STALLS, it is usually because it is

being overloaded or improperly used. RELEASE

TRIGGER IMMEDIATELY, remove drill bit

from work, and determine cause of stalling. DO

NOT CLICK TRIGGER ON AND OFF IN AN

ATTEMPT TO START A STALLED DRILL —

THIS CAN DAMAGE THE DRILL.

5. To minimize stalling or breaking through the

material, reduce pressure on drill and ease the bit

through the last fractional part of the hole.

6. Keep the motor running when pulling the bit

back out of a drilled hole. This will help prevent

jamming.

7. With variable speed drills there is no need to

center punch the point to be drilled. Use a

slow speed to start the hole and accelerate by

squeezing the trigger harder when the hole is

deep enough to drill without the bit skipping out.

DRILLING IN METAL

Start drilling with slow speed and increase to full

power while applying firm pressure on the tool. A

smooth even flow of metal chips indicates the proper

drilling rate. Use a cutting lubricant when drilling

metals. The exceptions are cast iron and brass which

should be drilled dry.

NOTE: Large [5/16" (8 mm) to 1/2" (13 mm)] holes in

steel can be made easier if a pilot hole [5/32"

(4 mm) to 3/16" (5 mm)] is drilled first.

DRILLING IN WOOD

Start drilling with slow speed and increase to full

power while applying firm pressure on the tool. Holes

in wood can be made with the same twist drills used

for metal. These bits may overheat unless pulled out

frequently to clear chips from the flutes. Work that is

apt to splinter should be backed up with a block of

wood.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

ENGLISH

WARNING: To reduce the risk of serious

personal injury, ALWAYS hold securely in

anticipation of a sudden reaction.

Proper hand position requires one hand on the side

handle (6), with the other hand on the main handle

(11).

Switching On and Off (ﬁ g. A)

• To run the tool, press the variable speed switch (1).

The pressure exerted on the variable speed switch

determines the tool speed.

• If necessary, press the lock-on button (2) for

continuous operation and release the switch.

The lock-on button works only in full speed,

forward rotation.

• To stop the tool, release the switch.

• To stop the tool in continuous operation, press

the switch brieﬂ y and release it. Always switch

off the tool when work is ﬁ nished and before

unplugging.

Screwdriving

• Select forward or reverse rotation.

Percussion Drilling (ﬁ g. A)

• Select the percussion mode.

• Press the switch (1).

Rotary Drilling (ﬁ g. A)

• Select the rotary drilling mode.

• Proceed as described for percussion drilling.

Drilling

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories.

WARNING: To reduce the risk of

personal injury, ALWAYS ensure

workpiece is anchored or clamped firmly.

If drilling thin material, use a wood “back-

up” block to prevent damage to the

material.

1. Use sharp drill bits only. For WOOD, use the

low speed setting and twist drill bits, spade bits,

power auger bits, or hole saws. For METAL, use

the low speed setting and steel twist drill bits or

hole saws.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D21717 T 2 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info