Bedienungsanleitung DeWalt D21720 T 4 (Seite 28 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

544708

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

ENGLISH

Percussion drilling:

simultaneous rotating and impacting for

concrete and masonry drilling operations.

• Select the required operating mode by rotating

the mode selector (5) to the required position.

Inserting and Removing a Bit (ﬁ g. A)

Keyless Chuck

• Open the chuck by turning the sleeve (9)

counterclockwise and insert the bit shank.

• Tighten ﬁ rmly by turning the sleeve clockwise.

Keyed Chuck

• Open the chuck by turning the sleeve (9)

counterclockwise and insert the bit shank.

• Put the chuck key (10) into each hole in the side

of the chuck and turn clockwise until tight.

• To remove the bit, proceed in reverse order.

Fitting the Side Handle (ﬁ g. A)

The side handle (6) can be ﬁ tted to suit both RH-

and LH-users.

WARNING: Always use the Drill with the

side handle properly assembled.

• Loosen the side handle.

• For RH-users, slide the side handle clamp over

the collar behind the chuck, handle at the left.

• For LH-users, slide the side handle clamp over

the colar behind the chuck, handle at the right.

• Rotate the side handle to the desired position

and tighten the handle.

Setting the Drilling Depth (ﬁ g. C)

• Insert the required drill bit into the chuck.

• Slacken the side handle (6).

• Fit the depth adjustment rod (7) through the hole

in the side handle clamp.

• Adjust the drilling depth as shown.

• Tighten the side handle.

Forward/reverse Slider (ﬁ g. A)

• To select forward or reverse rotation, use the

forward/reverse-switch (3) (see arrow on tool).

WARNING: Always wait until the motor

has come to a complete standstill before

changing the direction of rotation.

Two Gear Selector (ﬁ g. E)

This tool is ﬁ tted with a two gear selector (4) to vary

the speed/torque ratio.

• Release the ON/OFF-switch and select the

required position as the drill coasts to a stop.

Always align the selector arrow with the gear

symbol on the gear housing:

1 low speed/high torque

(drilling large holes or driving large screws)

2 high speed/low torque

(smaller holes, drilling in wood)

For speed rates, refer to the technical data.

WARNING: Do not change gears at full

speed or during use.

Chuck Removal (ﬁ g. F, G)

• Open the chuck jaws as far as possible.

• Insert a screwdriver into the chuck and remove

the chuck retaining screw (13) by turning

clockwise.

• Tighten an Allen key into the chuck and strike it

with a hammer as shown.

Prior to Operation

• Insert the appropriate bit.

• Mark the spot where the hole is to be drilled.

OPERATION

WARNING: To reduce the risk

of serious personal injury, turn

tool off and disconnect tool from

power source before making any

adjustments or removing/installing

attachments or accessories.

Instructions for Use

WARNING:

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework

and wiring.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D21720 T 4 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info