Bedienungsanleitung DeWalt D25144 (Seite 27 von 116) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

712255

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

ENGLISH

• This product is not intended for use by persons (including

children) suffering from diminished physical, sensory or

mental abilities; lack of experience, knowledge or skills

unless they are supervised by a person responsible for their

safety. Children should never be left alone with thisproduct.

Torque Limiting Clutch

All rotary hammerdrills are equipped with a torque limiting

clutch that reduces the maximum torque reaction transmitted

to the operator in case of jamming of a drill bit. This feature

also prevents the gearing and electric motor from stalling.

The torque limiting clutch has been factory-set and cannot

beadjusted.

ASSEMBLY AND ADJUSTMENTS



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect tool from power

source before making any adjustments or removing/

installing attachments or accessories. Be sure the

trigger switch is in the OFF position. An accidental start-up

can cause injury.

Selecting the Operating Mode

(Fig. B)

The tool can be used in the following operating modes:

Rotary drilling: for screwdriving and for drilling

into steel, wood and plastics

Hammerdrilling: for concrete and masonry

drilling operations.

Bit rotation: non-working position used only to

rotate a ﬂat chisel into the desired position

Hammering only (D25033, D25133, D25134,

D25143, D25144, D25263): for light chipping,

chiselling and demolition applications. In this

mode the tool can also be used as a lever to free

a jammed drillbit.

1. To select the operating mode, press the mode selector

button

5

and rotate the mode selector switch

4

until it

points to the symbol of the requiredmode.

2. Release the mode selector button and check that the mode

selector switch is locked inplace.



WARNING: Do not select the operating mode when the

tool isrunning.

Indexing the Chisel Position (Fig. B)

The chisel can be indexed and locked into differentpositions.

1. Press the mode selector button

5

and rotate the mode

selector switch

4

until it points to the “bit rotation/

hammerdrilling”position.

2. Rotate the chisel to the desiredposition.

3. Set the mode selector switch

4

to the “hammering

only”position.

4. Twist the chisel until it locks inposition.

Inserting and Removing SDS Plus Accessories

(Fig. C)

This tool uses SDS Plus accessories (refer to the inset in Fig.C for

a cross-section of an SDS Plus bit shank). We recommend using

professional accessoriesonly.

1. Clean and grease the bitshank.

2. Insert the bit shank into the SDS Plus tool holder

6

3. Push the bit down and turn it slightly until it ﬁts into

theslots.

4. Pull on the bit to check if it is properly locked. The

hammering function requires the bit to be able to move

axially several centimetres when locked in the toolholder.

5. To remove a bit, pull back the tool holder sleeve

10

and

pull out thebit.



WARNING: Always wear gloves when you change

accessories. The exposed metal parts on the tool and

accessory may become extremely hot duringoperation.

Fitting the Side Handle (Fig. D)

The side handle

8

can be ﬁtted to suit both right-handed and

left-handedusers.



WARNING: Do not use the tool without the side handle

properlyassembled.

1. Loosen the sidehandle.

2. For right-handed users: Slide the side handle clamp over

the collar behind the tool holder, handle at theleft.

For left-handed-users: Slide the side handle clamp over

the collar behind the tool holder, handle at theright.

3. Rotate the side handle to the desired position and tighten

thehandle.

Side Handle Work light (Fig. E)

D25144, D25263

The side handle on the D25144 and D25263 has a work

light

15

. The light is battery powered and operated by using

the on/off button

17

To replace the worklight’s batteries (CR2032 x 2):

1. Remove battery door screw

16

as shown in FigureE.

2. Replace the battery with the positive face

pointingoutwards.

3. Close the battery compartment and secure thescrew.

Setting the Drilling Depth (Fig. F)

1. Insert the required drill bit as describedabove.

2. Press the depth rod button

9

and keep itdepressed.

3. Fit the depth adjustment rod

7

through the hole in the

depth stopclamp.

4. Adjust the drilling depth asshown.

5. Release the depth stopclamp.

Reversing Lever (Fig. G)

The forward/reverse lever

3

is used to reverse the rotation of

the hammer for backing out fasteners or jammed bits in the

drill-onlyfunction.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D25144 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info