Bedienungsanleitung DeWalt D25263 (Seite 29 von 116) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

712256

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

ENGLISH

7. When drilling through a structure thicker than the depth of

the core bit, break away the round cylinder of concrete or

core inside the bit at regular intervals. To avoid unwanted

breaking away of concrete around the hole, ﬁrst drill a hole

the diameter of the center drill completely through the

structure. Then drill the cored hole halfway from eachside.

8. Always switch off the tool when work is ﬁnished and

beforeunplugging.

Rotary Drilling (Fig. A)

1. Hold down the mode selector button

5

then set the mode

selector switch

4

to the “rotary drilling”position.

2. Depending on your tool, follow either of the following

instructions:

- D25032, D25033, D25133, D25143, D25263: Fit the

chuck adapter/chuckassembly.

- D25134, D25144: Replace the

SDS Plus tool holder with the keylesschuck.

3. Proceed as described forhammerdrilling.



WARNING: Never use standard chucks in the

hammerdrillingmode.

Screwdriving (Fig. A)

1. Hold down the mode selector button

5

then set the mode

selector switch

4

to the rotary drillingposition.

2. Select the direction ofrotation.

3. Depending on your tool, follow either of the following

instructions:

- D25032, D25033, D25133, D25143, D25263: Insert

the special SDS Plus screwdriving adaptor for use with

hexagonal screwdriverbits.

- D25134, D25144: Replace the SDS Plus tool holder

with the keyless chuck

4. Insert the appropriate screwdriver bit. When driving slotted

head screws always use bits with a ﬁndersleeve.

5. Gently press the variable speed switch

1

to prevent

damage to the screw head. In reverse (LH) rotation the tool

speed is automatically reduced for easy screwremoval.

6. When the screw is ﬂush with the workpiece, release the

variable speed switch to prevent the screw head from

penetrating into theworkpiece.

Chipping and Chiselling (Fig. A)

D25033, D25133, D25134, D25143,

D25144, D25263

1. Hold down the mode selector button

5

then set the mode

selector switch

4

to the “hammering only”position.

2. Insert the appropriate chisel and rotate it by hand to lock it

intoposition.

3. Adjust the side handle

8

asrequired.

4. Switch on the tool and startworking.

5. Always switch off the tool when work is ﬁnished and

beforeunplugging.



WARNING:

• Do not use this tool to mix or pump easily combustible

or explosive ﬂuids (benzine, alcohol, etc.).

• Do not mix or stir in ﬂammable liquids

labelledaccordingly.

MAINTENANCE

Your

DeWALT

power tool has been designed to operate

over a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regularcleaning.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect tool from power

source before making any adjustments or removing/

installing attachments or accessories. Be sure the

trigger switch is in the OFF position. An accidental start-up

can cause injury.

• This machine is not user-serviceable. Take the tool to an

authorised

DeWALT

repair agent after approximately 40

hours of use. If problems occur before this time contact an

authorised

DeWALT

repairagent.

• The tool will automatically switch off when the carbon

brushes areworn.

Motor Brushes

DeWALT

uses an advanced brush system which automatically

stops the drill when the brushes wear out. This prevents serious

damage to the motor. New brush assemblies are available

at authorised

DeWALT

service centers. Always use identical

replacementparts.

Lubrication

Your power tool requires no additionallubrication.

Accessories and attachments used must be regularly lubricated

around the SDS Plusﬁtment.

Cleaning



WARNING: Blow dirt and dust out of the main housing

with dry air as often as dirt is seen collecting in and around

the air vents. Wear approved eye protection and approved

dust mask when performing thisprocedure.



WARNING: Never use solvents or other harsh chemicals

for cleaning the non-metallic parts of the tool. These

chemicals may weaken the materials used in these parts.

Use a cloth dampened only with water and mild soap.

Never let any liquid get inside the tool; never immerse any

part of the tool into aliquid.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D25263 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info