Bedienungsanleitung DeWalt D25313 (Seite 28 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

78627

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

E N G L I S H

For 115 V units with a power rating exceeding

1500 W, we recommend to ﬁt a plug to BS4343

standard.

Using an extension cable

If an extension cable is required, use an approved

extension cable suitable for the power input of this

machine (see technical data). The minimum

conductor size is 1.5 mm

When using a cable reel, always unwind the cable

completely.

Also refer to the table below.

Conductor size (mm

) Cable rating (Amperes)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.5 15 25 30 45 60

Voltage Amperes Cable rating (Amperes)

115 0 - 2.0 6 6 6 6 6 10

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

230 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

Assembly and adjustment

Prior to assembly and adjustment

always unplug the tool.

Selecting the operating mode (ﬁg. B)

The tool can be used in the following operating

modes:

Rotary drilling: for screwdriving and for

drilling into steel, wood and plastics

Hammer drilling: for concrete and

masonry drilling operations.

Hammering only: for light chipping,

chiselling and demolition applications.

In this mode the tool can also be used

as a lever to free a jammed drill bit.

Bit rotation: non-working position used

only to rotate a ﬂat chisel into the

desired position.

● To select the operating mode, press the safety

lock (4) and rotate the mode selector switch (3)

until it points to the symbol of the required mode.

● Release the safety lock and check that the

mode selector switch is locked in place.

Do not select the operating mode when

the tool is running.

Indexing the chisel position

The chisel can be indexed and locked into

51 different positions.

● Rotate the mode selector switch (3) until it

points to the "bit rotation" position.

● Rotate the chisel in the desired position.

● Set the mode selector switch (3) to the

"hammering only" position.

● Twist the chisel until it locks in position.

Inserting and removing SDS-plus

accessories

(ﬁg. C)

This tool uses SDS-plus

accessories (refer to the

inset in ﬁg. C for a cross-section of an SDS-plus

bit shank).

We recommend to use professional accessories only.

● Clean and grease the bit shank.

● Insert the bit shank into the tool holder (5).

● Push the bit down and turn it slightly until it ﬁts

into the slots.

● Pull on the bit to check if it is properly locked.

The hammering function requires the bit to be

able to move axially several centimetres when

locked in the tool holder.

● To remove a bit pull back the tool holder locking

sleeve (11) and pull out the bit.

Always wear gloves when you change

accessories. The exposed metal parts

on the tool and accessory may become

extremly hot during operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D25313 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info