Bedienungsanleitung DeWalt D25330K T 2 (Seite 26 von 112) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544663

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

ENGLISH

Replacing the Dust Cover (ﬁ g. 2)

The dust cover (e) prevents dust from entering into

the mechanism.

IMPORTANT: Replace a worn dust cover immediately.

1. Pull back the tool holder/locking sleeve (d) and

pull the dust cover (e) off.

2. Fit the new dust cover.

3. Release the tool holder/locking sleeve.

OPERATION

Instructions for Use

WARNING:

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework

and wiring.

• Apply a pressure of approx. 5 kg to

the tool. Excessive force does not

speed up chiselling but decreases tool

performance and may shorten tool life.

Proper Hand Position (ﬁ g. 1, 6)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the

side handle (f), with the other hand on the main

handle (g).

Switching On and Off (ﬁ g. 1, 5)

To run the tool, press the on/off switch (a).

For continuous operation, press and hold down the

switch (a), slide the lock-on slider (b) into the lock

position and release the switch.

To stop the tool, release the switch.

To stop the tool in continuous operation, press the

switch briefly and release it. Always switch off the

tool when work is finished and before unplugging.

Chipping and Chiselling (ﬁ g. 1)

Insert the appropriate chisel and rotate it into one of

12 positions.

Turn the tool on the tool and start working.

Always turn the tool off when work is finished and

before unplugging.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-ups

or when making repairs. Be sure the

trigger switch is in the OFF position. An

accidental start-up can cause injury.

Lubrication

Your power tool requires no additional lubrication.

Accessories and attachments used must be

regularly lubricated around the SDS Plus

fitment.

Cleaning

WARNING: Blow dirt and dust out of

the main housing with dry air as often as

dirt is seen collecting in and around the

air vents. Wear approved eye protection

and approved dust mask when

performing this procedure.

WARNING: Never use solvents or

other harsh chemicals for cleaning the

non-metallic parts of the tool. These

chemicals may weaken the materials

used in these parts. Use a cloth

dampened only with water and mild

soap. Never let any liquid get inside the

tool; never immerse any part of the tool

into a liquid.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D25330K T 2 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info