Bedienungsanleitung DeWalt D25330K (Seite 19 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

544662

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

ENGLISH

Also refer to the table below.

Conductor size (mm

) Cable rating (Amperes)

0.75 6

1.00 10

1.50 15

2.50 20

4.00 25

Cable length (m)

7.5 15 25 30 45 60

Voltage Amperes Cable rating (Amperes)

115 0-2.0 66 66 610

2.1 - 3.4 6 6 6 6 15 15

3.5 - 5.0 6 6 10 15 20 20

5.1 - 7.0 10 10 15 20 20 25

7.1 - 12.0 15 15 20 25 25 -

12.1 - 20.0 20 20 25 - - -

230 0 - 2.0 6 6 6 6 6 6

2.1 - 3.4 6 6 6 6 6 6

3.5 - 5.0 6 6 6 6 10 15

5.1 - 7.0 10 10 10 10 15 15

7.1 - 12.0 15 15 15 15 20 20

12.1 - 20.0 20 20 20 20 25 -

Assembly and adjustment

Prior to assembly and adjustment always

unplug the tool.

Inserting and removing SDS-plus

accessories

(fig. B)

This tool uses SDS-plus

accessories (refer to the

inset in fig. B for a cross-section of an SDS-plus

bit

shank).

We recommend to use professional accessories only.

• Clean and grease the bit shank.

• Insert the bit shank into the tool holder (4).

• Push the bit down and turn it slightly until it fits

into the slots.

• Pull on the bit to check if it is properly locked.

The hammering function requires the bit to be

able to move axially several centimetres when

locked in the tool holder.

• To remove a bit pull back the tool holder locking

sleeve (7) and pull out the bit.

Indexing the chisel position (fig. C)

The chisel can be indexed and locked into

12 different positions.

• Insert the chisel as described above.

• Rotate the collar (3) in the direction of the arrow

until the chisel is in the desired position.

Fitting the side handle (fig. D)

The side handle (6) can be fitted to suit both

RH- and LH-users.

Always use the tool with the side handle

properly assembled.

• Loosen the side handle.

• For RH-users, slide the side handle clamp over the

collar behind the tool holder, handle at the left.

• For LH-users, slide the side handle clamp over the

collar behind the tool holder, handle at the right.

• Rotate the side handle to the desired position

and tighten the handle.

Replacing the dust cover (fig. B)

The dust cover (5) prevents dust ingress into the

mechanism. Replace a worn dust cover

immediately.

• Pull back the tool holder locking sleeve (7) and

pull the dust cover (5) off.

• Fit the new dust cover.

• Release the tool holder locking sleeve.

Instructions for use

Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework and wiring.

• Apply a pressure of approx. 5 kg to the tool.

Excessive force does not speed up chiselling but

decreases tool performance and may shorten

tool life.

Switching on and off (fig. A & E)

• To run the tool, press the on/off switch (1).

• For continuous operation, press and hold down

the switch (1), slide the lock-on slider (2) into the

lock position and release the switch.

• To stop the tool, release the switch.

• To stop the tool in continuous operation, press

the switch briefly and release it. Always switch off

the tool when work is finished and before

unplugging.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D25330K Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info