Bedienungsanleitung DeWalt D25404K T-3 (Seite 30 von 132) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

544495

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

ENGLISH

Proper Hand Position (ﬁ g. 1, 7)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the

side handle (h), with the other hand on the main

handle (l).

Switching On and Off (ﬁg. 1)

To run the tool, press the variable speed switch (a).

The pressure exerted on the variable speed switch

determines the tool speed.

To stop the tool, release the switch.

Hammerdrilling (ﬁg. 1)

DRILLING WITH A SOLID BIT

1. Set the mode selector switch (b) to the

“hammerdrilling” position.

2. Insert the appropriate drill bit. For best results

use high quality carbide-tipped bits.

3. Adjust the side handle (h) as required.

4. If necessary, set the drilling depth.

5. Mark the spot where the hole is to be drilled.

6. Place the drill bit on the spot and switch on the

tool.

7. Always switch off the tool when work is ﬁnished

and before unplugging.

Drilling with a Core Bit

1. Set the mode selector (b) to the “hammer

drilling” position.

2. Adjust the side handle (h) as required.

3. Insert the appropriate core bit.

4. Assemble the centerdrill into the core bit.

5. Place the centerdrill on the spot and press the

variable speed switch (a). Drill until the core

penetrates into the concrete approx. 1 cm.

6. Stop drilling and remove the centerdrill. Place

the core bit back into the hole and continue

drilling.

7. When drilling through a structure thicker than

the depth of the core bit, break away the round

cylinder of concrete or core inside the bit at

regular intervals. To avoid unwanted breaking

away of concrete around the hole, ﬁrst drill a

hole the diameter of the centerdrill completely

through the structure. Then drill the cored hole

halfway from each side.

8. Always switch off the tool when work is ﬁnished

and before unplugging.

Rotary Drilling (ﬁg. 1)

1. Set the mode selector switch (b) to the “rotary

drilling” position.

2. Replace the tool holder with the chuck

(DT7018).

3. Proceed as described for hammerdrilling.

WARNING: Never use standard chucks

in the hammerdrilling mode.

Chipping and Chiselling (ﬁg. 1)

1. Set the mode selector switch (b) to the

hammering only position.

2. Insert the appropriate chisel and rotate it by

hand to lock it into one of 24 positions.

3. Adjust the side handle (h) as required.

4. Switch on the tool and start working.

5. Always switch off the tool when work is ﬁnished

and before unplugging.

WARNING:

• Do not use this tool to mix or pump

easily combustible or explosive ﬂuids

(benzine, alcohol, etc.).

• Do not mix or stir inﬂammable liquids

labelled accordingly.

MAINTENANCE

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-ups

or when making repairs. Be sure the

trigger switch is in the OFF position. An

accidental start-up can cause injury.

• This machine is not user-serviceable. Take the

tool to an authorised DEWALT repair agent after

approximately 40 hours of use. If problems

occur before this time contact an authorised

DEWALT repair agent.

• The tool will automatically switch off when the

carbon brushes are worn.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D25404K T-3 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info