Bedienungsanleitung DeWalt D25500K T-2 (Seite 31 von 132) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

544499

Zoom out

Zoom in

Vorherige Seite

1/132

Nächste Seite

ENGLISH

2. Insert the bit shank into the tool holder (f), and

press and turn the bit slightly until the sleeve

snaps into position.

3. Pull on the bit to check if it is properly locked.

The hammering function requires the bit to be

able to move axially several centimetres when

locked in the tool holder.

4. To remove a bit pull back the tool holder locking

sleeve (f) and pull the bit out of the tool holder.

Selecting the Operating Mode

(ﬁ g. 5)

The tool can be used in two operating modes:

Hammerdrilling: for concrete and

masonry drilling operations.

Hammering only: for light chipping,

chiselling and demolition applications.

In this mode the tool can also be used

as a lever to free a jammed drill bit.

1. To select the operating mode, press the safety

lock (e) and rotate the mode selector switch

(d) until it is points to the symbol of the required

mode.

2. Release the safety lock and check that the

mode selector switch is locked in place.

Indexing the Chisel Position (ﬁ g. 5, 6)

The chisel can be indexed and locked into 8 different

positions (fig. 6).

1. Rotate the mode selector switch (d) until it

points upward.

2. Rotate the chisel in the desired position.

3. Set the mode selector switch (d) to the

“hammering only” position.

4. Twist the chisel until it locks in position.

Setting the Electronic Speed and

Impact Control Dial (ﬁ g. 2)

Turn the dial (b) to the desired level. The higher the

number, the greater the speed and impact energy.

With dial settings from 1 (low) to 5 (full power) the

tool is extremely versatile and adaptable for many

different applications. The required setting is a matter

of experience. e.g.:

— when chiselling or drilling in soft, brittle

materials or when minimum break-out is

required, set the dial to 1 or 2 (low);

— when breaking or drilling in harder

materials, set the dial to 5 (full power).

D25600

With dial settings from 1 to 7 the tool allows a further

fine-adjustment to the choice of application.

Assembling and Fitting the Side

Handle (ﬁ g. 7–10)

The side handle (h) can be mounted in front or in

rear position on either side of the machine to suit

both RH- and LH-users.

CAUTION: Always operate the tool with

the side handle properly assembled.

MOUNTING IN FRONT POSITION (FIG. 7, 8)

1. Snap the steel ring (p) over the collar (g) behind

the tool holder (f). Squeeze both ends together,

mount the bush (n) and insert the pin (o).

2. Place the side handle clamp (m) and screw on

the clamp wheel (i). Do not tighten.

3. Screw the side handle (h) into the clamp wheel

and tighten it.

4. Rotate the side handle mounting assembly to

the desired position. For drilling horizontally

with a heavy drill bit, we recommend to place

the side handle at an angle of approx. 20° for

optimum control (fig. 8).

5. Lock the side handle mounting assembly in

place by tightening the clamp wheel (i).

MOUNTING IN REAR POSITION (FIG. 9, 10)

The rear position is particularly useful when drilling

overhead or down into a floor. Refer to fig. 10.

1. Unscrew the side handle (h) and remove it

from the front position. Leave the side handle

mounting assembly in front position so that the

depth adjustment rod can still be used.

2. Screw the side handle directly into one of the

rear side handle positions (j) on either side of the

tool.

Setting the Drilling Depth (ﬁ g. 11)

1. Insert the required drill bit.

2. Loosen the clamp nut (q) and fit the depth

adjustment rod (k) through the hole in the side

handle clamp.

3. Push the drill bit into a surface at a right angle

and adjust the depth adjustment rod (k) as

shown.

4. Tighten the clamp nut (q).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D25500K T-2 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt D25500K T-2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info