Bedienungsanleitung DeWalt D25553 (Seite 8 von 36) (Englisch, Französisch, Spanisch, Alle Sprachen)

723580

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

ENGLISH

Fig. D

13 16

Two-Stage Clutch/E-ClutchTM (Fig. E)

NOTICE: Always turn the tool off before changing

torque control settings or damage to tool mayresult.

Two-stage clutch

D25603, D25651

Clutch Setting 1 14  is designed for most hammerdrilling

applications and is designed to easily clutch out when the

drill bit encounters re-bar or other foreignsubstances.

Clutch Setting 2 11  is designed for higher torque

applications such as core-bits and deep hole hammerdrilling

and is designed to clutch out at a higher torquethreshold.

Move the torque control lever 8  to Clutch Setting 1 or 2 as

needed forapplication.

NOTE: Allow the motor housing to rotate a little while

changingtorque.

NOTE: If it is not possible to select Clutch Setting 2, run the

unit under load and tryagain.

Each time the tool is plugged in, it will automatically default

to Clutch Setting 1, the most sensitivesetting.

E-CLUTCH™

D25603

In addition, E-Clutch™ offers increased user comfort and

safety through an on-board antirotation technology capable

of detecting if the user loses control of the hammer. When a

jam is detected, the torque and speed are reduced instantly.

The red indicator LED 9  illuminates when the E-Clutch™

isengaged.

Fig. E

Electronic Speed and Impact Control

(Fig. E)

D25651, D25601, D25603, D25831,

D25851

The electronic speed and impact control allows the

use of smaller drill bits without the risk of bit breakage,

hammerdrilling into light and brittle materials without

shattering and optimal tool control for precisechipping.

To set the control dial, turn the dial7 to the desired level.

The higher the number, the greater the speed and impact

energy. Dial settings make the tool extremely adaptable for

many different appli cations. The required setting depends

on the bit size and hardness of material beingdrilled.

Mode Selector (Fig. A)

NOTICE: Never change the mode while the unit is

running. Tool must come to a complete stop before

activating the mode selector button or damage to the

tool mayresult.

CAUTION: Do not change to hammerdrill mode with

chisel bit in tool holder. Personal injury and damage

to tool mayresult.

The D25501, D25553, D25601, D25603, and D25651 use

two operating modes. To select the required operating

mode, rotate the mode selector6 until the arrow points to

the hammerdrilling or the chipping icon. The D25831 and

D25851 use only the chippingmode.

Hammerdrilling Mode ( )

D25501, D25553, D25601, D25603,

D25651

The tool simultaneously rotates and impacts the

work. This mode is appropriate for all concrete and

masonryoperations.

Chipping Mode ( )

D25831, D25851

The spindle lock is engaged during chipping mode

so the tool impacts the work without rotating. This

mode is appropriate for light chipping, chiseling and

demolitionapplications.

NOTE: In chipping mode, the hammerdrill can also be used

as a lever to free a jammed drillbit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D25553 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info