Bedienungsanleitung DeWalt D25601 (Seite 37 von 158) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

497574

Zoom out

Zoom in

Vorherige Seite

1/158

Nächste Seite

ENGLISH

3. Release the button to lock rod into position.

When drilling with the depth rod, stop when end

of rod reaches surface of material.

OPERATION

Instructions for Use

WARNING: Always observe the safety

instructions and applicable regulations.

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-

ups or when making repairs. Be sure

the trigger switch is in the OFF position.

An accidental start-up can cause injury.

WARNING: Tool bits may be hot and

gloves should be worn when changing

or removing them to avoid personal

injury.

WARNING:

• Be aware of the location of pipework

and wiring.

• Apply only a gentle pressure to the

tool (approximately 20 kg). Excessive

force does not speed up drilling but

decreases tool performance and may

shorten tool life.

• Always hold the tool ﬁrmly with both

hands and ensure a secure stance.

Always operate the tool with the side

handle properly assembled.

NOTE: Operating temperature is -7˚ to +40˚C (19˚

to 104˚ F). Using the tool outside of this temperature

range will decrease the life of the tool.

Proper Hand Position (ﬁ g. 6)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the

side handle (c), with the other hand on the main

handle (d).

Switching On and Off (ﬁ g. 1)

D25501, D25601, D25602, D25603

To turn the tool on, depress the trigger switch (a).

To stop the tool, release the trigger switch.

D25601, D25602, D25603

The lock-on slider (b) allows the trigger switch (a) to

be locked on in chiselling mode only. If the lock-on

button is activated in drilling mode, as a feature the

tool will switch off automatically.

To turn the tool on, press the trigger switch(a).

To stop the tool, release the switch.

For continuous operation, press and hold down the

switch (a), slide the lock-on button (b) upwards and

release the switch.

To stop the tool in continuous operation, press the

switch briefly and release it. Always switch off the

tool when work is finished and before unplugging.

D25831

To turn the tool on, press the on/off rocker switch (a)

at the lower part of the trigger.

To stop the tool, press the on/off rocker switch at

the upper part of the trigger.

Hammerdrilling

To turn the tool on, press the on/off switch(a).

To stop the tool, release the switch.

Drilling with a Solid Bit (ﬁ g. 1)

D25501, D25601, D25602, D25603

1. Insert the appropriate drill bit.

2. Set the mode selector switch (f) to the

hammerdrilling position.

3. D25601, D25602, D25603 only: Set the

electronic speed and impact control dial(g).

4. Fit and adjust the side handle (c).

5. Mark the spot where the hole is to be drilled.

6. Place the drill bit on the spot and switch on the

tool.

7. Always switch off the tool when work is finished

and before unplugging.

Drilling with a Core Bit (ﬁ g. 1)

1. Insert the appropriate core bit.

2. Assemble the centerdrill into the core bit.

3. Set the mode selector switch (f) to the

hammerdrilling position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D25601 Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info