Bedienungsanleitung DeWalt D25712K (Seite 35 von 158) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544646

Zoom out

Zoom in

Vorherige Seite

1/158

Nächste Seite

ENGLISH

Service Indicator LEDs (ﬁ g. 3)

The yellow brushwear indicator LED (s) lights up

when the carbon brushes are nearly worn out to

indicate that the tool needs servicing within the next

8 hours of use.

D25711, D25712, D25713, D25762, D25763

The red service indicator LED (r) lights up if the

lock-on button (b) is used in any mode except the

chipping mode. On models fitted with Ultimate

Torque Control (UTC), the red LED indicator (r) lights

up if the anti-rotational device is activated. The red

indicator starts to flash if there is a fault with the tool

or the brushes have completely worn out (refer to

Brushes under Maintenance).

D25870

The red service indicator LED (r) lights up if there is

a fault with the tool or the brushes have completely

worn out (refer to Brushes under Maintenance).

Fully Vibration-dampened Main

Handle (ﬁ g. 1)

The dampers in the main handle (d) absorb the

vibrations transmitted to the user. This improves user

comfort during the operation.

Electrical Safety

The electric motor has been designed for one

voltage only. Always check that the power supply

corresponds to the voltage on the rating plate.

Your DEWALT tool is double insulated in

accordance with EN 60745; therefore no

earth wire is required.

WARNING: 115 V units have to

be operated via a fail-safe isolating

transformer with an earth screen

between the primary and secondary

winding.

If the supply cord is damaged, it must be replaced

by a specially prepared cord available through the

DEWALT service organisation.

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in

the plug.

• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be

made to the earth terminal.

Follow the fitting instructions supplied with good

quality plugs. Recommended fuse: 13 A.

Using an Extension Cable

If an extension cable is required, use an approved 3–

core extension cable suitable for the power input of

this tool (see technical data).The minimum conductor

size is 1.5 mm

; the maximum length is 30 m.

When using a cable reel, always unwind the cable

completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of

injury, turn unit off and disconnect

machine from power source before

installing and removing accessories,

before adjusting or changing set-

ups or when making repairs. Be sure

the trigger switch is in the OFF position.

An accidental start-up can cause injury.

WARNING: Tool bits may be hot and

gloves should be worn when changing

or removing them to avoid personal

injury.

Assembling and Fitting the Side

Handle (ﬁ g. 2A, 2B)

The side handle (c) can be mounted on either side

of the machine to suit both right- and left-handed

users.

WARNING: Always operate the

tool with the side handle properly

assembled.

D25711, D25712, D25713, D25762, D25763

MOUNTING IN FRONT POSITION (FIG. 2A)

1. Snap the steel ring (j) over the collar (n) behind

the tool holder (l). Squeeze both ends together,

mount the bush (k) and insert the pin (m).

2. Place the side handle clamp (i) and screw on

the clamp wheel (h). Do not tighten.

WARNING: Once assembled, the side

handle clamp should never be removed.

3. Screw the side handle (c) into the bush (k) and

then into clamp wheel. Tighten securely.

4. Rotate the side handle mounting assembly to

the desired position. For drilling horizontally with

a heavy drill bit, we recommend to place the

side handle at an angle of approximately 20° for

optimum control.

5. Lock the side handle mounting assembly in

place by tightening the clamp wheel (h).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D25712K Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info