Bedienungsanleitung DeWalt D28111 (Seite 26 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

446540

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

ENGLISH

d Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

e Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tools operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

f Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

g Use the power tool, accessories and tool bits

etc., in accordance with these instructions

and in the manner intended for the particular

type of power tool, taking into account the

working conditions and the work to be

performed. Use of the power tool for operations

different from those intended could result in a

hazardous situation.

5 Service

a Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the

power tool is maintained.

Additional safety rules for grinders

• Your grinder has been designed for grinding and

cutting masonry and steel.

Do not cut or grind light metal with a

magnesium content exceeding 80%

since this type of metal is flammable.

• Do not use any accessories other than fibre

reinforced grinding and cutting discs.

• Use only plain or centre-recessed grinding and

cutting discs.

• Use the grinding and cutting discs recommended

by the manufacturer only.

• The max. allowable speed of the grinding wheel

or cutting disc, or any other suitable accessory,

must always be equal to or greater than the no-

load speed of the tool specified on the nameplate.

• Do not cut workpieces requiring a maximum

depth of cut exceeding that of the cutting disc.

• Do not use grinding and cutting discs that do not

conform to the dimensions stated in the technical

data. Do not use any spacers to make a disc fit

onto the spindle.

• Inspect grinding and cutting discs before each

use. Do not use chipped, cracked or otherwise

defective discs.

• If provided, ensure that blotters are used when

the disc is fitted onto the spindle.

• When applying a threaded hole disc, ensure that

the thread is long enough to accept the spindle.

• Ensure that the grinding or cutting disc is

mounted correctly before use.

• Let the tool run at no-load in a safe position for at

least 30 seconds. If there is a considerable

vibration or if any other defect occurs, stop the

tool and check it to determine the cause.

• Do not operate this tool without the guard in place.

• Check that the workpiece is properly supported.

• Do not operate the tool near flammable liquids,

gases or dust. Sparks or hot chips from cutting

or arcing motor brushes may ignite combustible

materials.

• Do not operate the tool while standing in line with

the disc. Keep other persons away from the work

area.

• Do not use cutting discs for side grinding.

• Do not operate the spindle lock while the tool is

running.

• Beware that after switching off the tool the wheel

continues to rotate for a short period.

• Always store grinding and cutting discs in a dry

place.

• Ensure that the ventilation openings are kept clear

when working in dusty conditions. If it should

become necessary to clear the ventilation

openings, disconnect the tool from the mains

supply first and avoid damaging the internal parts

by using non-metallic objects.

• Always wear eye and ear protection. Preferably

wear other personal protective equipment such

as dust mask, gloves and a helmet.

Using flap discs

Warning: Metal dust build-up

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D28111 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt D28111

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info