Bedienungsanleitung DeWalt D28132C T 2 (Seite 46 von 216) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

547136

Zoom out

Zoom in

Vorherige Seite

1/216

Nächste Seite

ENGLISH

CAUTION: If the guard cannot be

tightened by the adjusting screw, do

not use the tool. To reduce the risk of

personal injury, take the tool and guard

to a service centre to repair or replace

the guard.

KEYLESS GUARD (FIG. 3)

D28113/D28130/D28132C/D28134/D28135/D28141

1. Place the angle grinder on a table, spindle (o)

up.

2. Release the clamping lock (g) and hold the

guard (c) over the tool as shown.

3. Align the lugs (k) with the notches (l).

4. Press the guard down and rotate it to the

required position.

5. If required, increase the clamping force by

tightening the screw (m).

6. Tighten the clamping lock.

7. To remove the guard, release the clamping lock.

Fitting and Removing a Grinding or

Cutting Disc (ﬁ g. 1, 4, 5)

WARNING: Do not use a damaged

disc.

1. Place the tool on a table, guard up.

2. Fit the backing flange (i) correctly onto the

spindle (o) (fig. 4).

3. Place the disc (n) on the backing flange (i).

When fitting a disc with a raised centre, make

sure that the raised centre (j) is facing the

backing flange (i).

4. Screw the threaded clamp nut (h) onto the

spindle (o) (fig. 5):

a. The ring on the threaded clamp nut (h) must

face towards the disc when fitting a grinding

disc (fig. 5A);

b. The ring on the threaded clamp nut (h) must

face away from the disc when fitting a cutting

disc (fig. 5B).

5. Press the spindle lock button (b) and rotate the

spindle (o) until it locks in position.

6. Tighten the threaded clamp nut (h) with the two-

pin spanner supplied.

7. Release the spindle lock.

8. To remove the disc, loosen the threaded clamp

nut (h) with the two-pin spanner.

Fitting and Removing a

Backing Pad/Sanding Sheet

(ﬁ g. 1, 5)

1. Place the tool on a table, guard up.

2. Remove the backing flange (i).

3. Place the rubber backing pad correctly onto the

spindle (o).

4. Place the sanding sheet on the rubber backing

pad.

5. Screw the threaded clamp nut (h) onto the

spindle. The ring on the threaded clamp nut (h)

must face towards the rubber backing pad.

6. Press the spindle lock button (b) and rotate the

spindle (o) until it locks in position.

7. Tighten the threaded clamp nut (h) with the two-

pin spanner.

8. Release the spindle lock

9. To remove the rubber backing pad, loosen the

threaded clamp nut (h) wih the two-pin spanner.

Fitting a Wire Cup Brush

Screw the wire cup brush directly onto the spindle

without the use of the spacer and threaded flange.

Prior to Operation

• Install the guard and appropriate disc or wheel.

Do not use excessively worn discs or wheels.

• Do not use a damaged accessory. Before each

use inspect the accessory such as abrasive

wheels for chips and cracks, backing pad for

cracks, tear or excess wear, wire brush for loose

or cracked wires. If power tool or accessory

is dropped, inspect for damage or install an

undamaged accessory. After inspecting and

installing an accessory, position yourself and

bystanders away from the plane of the rotating

accessory and run the power tool at maximum

no-load speed for one minute. Damaged

accessories will normally break apart during this

test time.

• Be sure the inner and outer flange are mounted

correctly. Follow the instructions given in the

Grinding and Cutting Accessory Chart.

• Make sure the disc or wheel rotates in the

direction of the arrows on the accessory and

the tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D28132C T 2 Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info