Bedienungsanleitung DeWalt D28141 (Seite 29 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

446547

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

ENGLISH

• Press the spindle lock (2) and rotate the spindle

(11) until it locks in position.

• Tighten the flange (14) with the two-pin spanner

supplied.

• Release the spindle lock.

• To remove the disc, loosen the flange (14) with

the two-pin spanner.

Do not use a damaged disc.

Mounting the side handle (fig. D)

• Screw the side handle (4) tightly into one of the

holes (14) on either side of the gear case.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Ensure all materials to be ground or cut

are secured in place.

• Apply only a gentle pressure to the tool.

Do not exert side pressure on the disc.

• Avoid overloading. Should the tool

become hot, let it run a few minutes

under no load condition.

Prior to operation:

• Install the guard and appropriate disc or wheel.

Do not use excessively worn discs or wheels.

• Be sure the inner and outer flange are mounted

correctly.

• Make sure the disc or wheel rotates in the direction

of the arrows on the accessory and the tool.

Switching on and off (fig. A)

• To run the tool, press the on/off switch (1).

• For continuous operation, press the switch

completely forward.

• To stop the tool, release the switch. To stop the

tool in continuous operation, press on the back

part of the switch.

Do not switch the tool on or off when

under load.

Metal applications

• When using the tool in metal applications, make

sure that a residual current device (RCD) has

been inserted to avoid residual risks caused by

metal swarf.

• If the power supply is shut off by the RCD, take

the tool to authorised DEWALT repair agent.

In extreme working conditions, conductive

dust can accumulate inside the machine

housing when working with metal. This

can result in the protective insulation in

the machine becoming degraded with a

potential risk of an electrical shock.

To avoid build-up of metal swarf inside the machine,

we recommend to clear the ventilation slots on a

daily basis. See “Maintenance”.

Using flap discs

Warning: Metal dust build-up

• Extensive use of flap discs in metal applications

can result in the increased potential for electric

shock. To reduce this risk, insert an RCD before

use and clean the ventilation slots daily by blowing

dry compressed air into the ventilation slots in

accordance with the below maintenance

instructions.

Optional accessories

Consult your dealer for further information on the

appropriate accessories.

Maintenance

Your DEWALT power tool has been designed to

operate over a long period of time with a minimum

of maintenance. Continuous satisfactory operation

depends upon proper tool care and regular cleaning.

Pop-off brushes

The motor will be automatically shut off indicating

that the carbon brushes are nearly worn out and that

the tool needs servicing. The carbon brushes are not

user-serviceable. Take the tool to an authorised

DEWALT repair agent.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D28141 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt D28141

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info