Bedienungsanleitung DeWalt D28151 T 1 (Seite 21 von 92) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

547338

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

ENGLISH

Warning! The use of any accessory or attachment

or performance of any operation with this tool

other than those recommended in this instruction

manual may present a risk of personalinjury.

14 Check for damaged parts

Before use, carefully check the tool and mains

cable for damage. Check for misalignment and

seizure of moving parts, breakage of parts,

damage to guards and switches and any other

conditions that may affect its operation.

Ensure that the tool will operate properly and

perform its intended function. Do not use the tool

if any part is damaged or defective. Do not use

the tool if the switch does not turn it on and off.

Have any damaged or defective parts replaced

by an authorised DEWALT repair agent. Never

attempt any repairs yourself.

15 Unplug tool

Switch off and wait for the tool to come to a

complete standstill before leaving it unattended.

Unplug the tool when not in use, before changing

any parts of the tools, accessories or

attachments and before servicing.

16 Avoid unintentional starting

Do not carry the tool with a finger on the switch.

Be sure that the tool is switched off before

plugging in.

17 Do not abuse cord

Never carry the tool by its cord. Never pull the

cord to disconnect from the socket. Keep the

cord away from heat, oil and sharp edges.

18 Store idle tools

When not in use, tools must be stored in a dry place

and locked up securely, out of reach of children.

19 Maintain tools with care

Keep the tools in good condition and clean for

better and safer performance. Follow the

instructions for maintenance and changing

accessories. Keep all handles and switches dry,

clean and free from oil and grease.

20 Repairs

This tool is in accordance with the relevant safety

regulations. Have your tool repaired by an

authorised DEWALT repair agent. Repairs should

only be carried out by qualified persons using

original spare parts; otherwise this may result in

considerable danger to the user.

Additional safety rules for grinders

• Your grinder has been designed for grinding and

cutting masonry and steel.

Do not cut or grind light metal with a

magnesium content exceeding 80%

since this type of metal is flammable.

• Do not use any accessories other than fibre

reinforced grinding and cutting discs.

• Use the grinding and cutting discs recommended

by the manufacturer only.

• The max. allowable speed of the grinding wheel

or cutting disc must always be equal to or

greater than the no-load speed of the tool

specified on the nameplate.

• Do not cut workpieces requiring a maximum

depth of cut exceeding that of the cutting disc.

• Do not use grinding and cutting discs that do not

conform to the dimensions stated in the technical

data. Do not use any spacers to make a disc fit

onto the spindle.

• Inspect grinding and cutting discs before each

use. Do not use chipped, cracked or otherwise

defective discs.

• If provided, ensure that blotters are used when

the disc is fitted onto the spindle.

• When applying a threaded hole disc, ensure that

the thread is long enough to accept the spindle.

• Ensure that the grinding or cutting disc is

mounted correctly before use.

• Let the tool run at no-load in a safe position for at

least 30 seconds. If there is a considerable

vibration or if any other defect occurs, stop the

tool and check it to determine the cause.

• Do not operate this tool without the guard in place.

• Check that the workpiece is properly supported.

• Do not operate the tool near flammable liquids,

gases or dust. Sparks or hot chips from cutting

or arcing motor brushes may ignite combustible

materials.

• Do not operate the tool while standing in line with

the disc. Keep other persons away from the work

area.

• Do not use cutting discs for side grinding.

• Do not operate the spindle lock while the tool is

running.

• Beware that after switching off the tool the wheel

continues to rotate for a short period.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D28151 T 1 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt D28151 T 1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info