Bedienungsanleitung DeWalt D28423C T 2 (Seite 26 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

548665

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

ENGLISH

• Fit the inner ﬂ ange (10) correctly onto the spindle

(11) (ﬁ g. C1).

• Place the disc (12) on the ﬂ ange (10) (ﬁ g. C2).

When ﬁ tting a disc with a raised center, make

sure that the raised centre (13) is facing the

ﬂ ange (10).

• Screw the outer ﬂ ange (14) onto the spindle (11)

(ﬁ g. C3):

- the ring on the ﬂ ange (14) must face towards

the disc when ﬁ tting a grinding disc (A);

- the ring on the ﬂ ange (14) must face away from

the disc when ﬁ tting a cutting disc (B).

• Press the spindle lock (3) and rotate the spindle

(11) until it locks in position (ﬁ g. C2)

• Tighten the ﬂ ange (14) with the two-pin spanner

supplied.

• Release the spindle lock.

• To remove the disc, loosen the ﬂ ange (14) with

the two-pin spanner.

Do not use a damaged disc.

Mounting the side handle (ﬁ g. D1 & D2)

• For grinding, screw the side handle (5) tightly into

one of the holes (15) on either side of the gear

case (ﬁ g. D1).

• For cutting, screw the side handle (5) tightly into

the top hole (16) or into one of the holes (17) on

either side of the gear case (ﬁ g. D2).

D28423/D28432C - Rotating the main handle

(ﬁ g. E1 & E2)

The rotary handle facilitates a more comfortable

handling in cutting applications with the side handle

mounted in the top hole.

The rotary handle has locations at 30°, 60° and 90°

both left and right.

• Pull the spring-loaded tab (18) to unlock the

rotary mechanism (ﬁ g. E1). Hold the tab in the

pulled-out position.

• Rotate the handle (19) into the desired position

(ﬁ g. E2).

• Release the tab and lock it in position.

• Check that the rotary mechanism is locked.

Do not use the tool unless the rotary

handle is in the locked postion.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Ensure all materials to be ground or cut

are secured in place.

• Apply only a gentle pressure to the tool.

Do not exert side pressure on the disc.

• Avoid overloading. Should the tool

become hot, let it run a few minutes

under no load condition.

Prior to operation:

• Install the guard and appropriate disc or wheel.

Do not use excessively worn discs or wheels.

• Be sure the inner and outer ﬂ ange are mounted

correctly.

• Make sure the disc or wheel rotates in the direction

of the arrows on the accessory and the tool.

Switching on and off (ﬁ g. A)

The on/off switch is equipped with an unlocking

switch or a locking switch for continuous operation.

On/off switch (1) with locking switch (2)

• To run the tool, depress the locking switch (2)

and subsequently operate the on/off switch (1).

• Release the locking switch (2).

• To stop the tool, press the on/off switch again.

On/off switch (1) with unlocking switch (2)

(France only)

• To run the tool, depress the unlocking switch (2)

and subsequently operate the on/off switch (1).

• Release the unlocking switch (2).

• To stop the tool, release the switch.

Do not switch the tool on or off when

under load.

Consult your dealer for further information on the

appropriate accessories.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

DeWalt D28423C T 2 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von DeWalt D28423C T 2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info